Enclosures and housings
Profiler Assembly Exploded
- Bounding box
- 600.2 × 600.0 × 350.2 mm
- Engine
- Precision B-rep
- Parameters
- 40
- Published
- September 2, 2026
Download
Free to download and use. See the terms.
The prompt
Model in mm. Do not model threads, fasteners or internal electronics — nobody will see them and they'll eat your day. Three bodies only: 1. Surface float — squat discus, roughly 600 mm diameter × 350 mm tall. On top: a short mast with an antenna dome, a small louvered radiation shield (a white ribbed cylinder, this is the air temperature sensor), a lifting eye. Underneath: a hard point where the wire attaches. No solar panels — we deliberately don't use them. Yellow/orange gloss. 2. The crawler — elongated, roughly 700 mm long × 140 mm diameter, faired at both ends, slightly torpedo-like. Features that must read clearly: a vertical channel through the body where the wire passes; a visible cam housing on one side (a small window or a bulge is enough); a sensor cage at the top end holding two or three probes; a foam collar around the middle. Orange body, dark grey fairings. 3. Terminal downweight — a cylindrical mass or a stack of discs at the bottom of the wire, with a small rubber bumper collar just above it. Polished metal, black bumper. Plus the wire itself: a thin swept cylinder. Don't model 500 m of it — model about a metre and use a break, or just crop it in the render. Deliverables, in priority order: View A — hero, and this is the one that matters. 3/4 isometric of the whole assembly with the wire broken, so float, crawler and downweight are all in one frame. 1920×1080 minimum, PNG. Due T+4. View B — the crawler, labelled. Same body, exploded or cut away enough to show the cam and the wire channel, with room around it for callouts. Due T+7 if there's time. View C — dimensioned side elevation. Not a render — an actual drawing view with key dimensions. Only if A and B are done. Dont take the dimensions seriously just make the model look great and generate images for reference for me to replicate on fusion/cad https://www.youtube.com/watch?v=V1dP4Kvc7eE
Parameters
| Name | Value | Range |
|---|---|---|
| Layout Gap | 800 mm | 300 – 2500 |
| Float Diameter | 600 mm | 200 – 1200 |
| Float Height | 350 mm | 100 – 700 |
| Float Edge Fillet | 40 mm | 0 – 200 |
| Mast Diameter | 40 mm | 15 – 120 |
| Mast Height | 150 mm | 50 – 400 |
| Antenna Dome Radius | 45 mm | 10 – 150 |
| Shield Diameter | 80 mm | 30 – 250 |
| Shield Height | 100 mm | 20 – 300 |
| Shield Rib Count | 10 mm | 3 – 30 |
| Shield Rib Depth | 5 mm | 1 – 20 |
| Lifting Eye Ring Diameter | 70 mm | 30 – 200 |
| Lifting Eye Ring Tube Diameter | 12 mm | 2 – 40 |
| Lifting Eye Base Diameter | 45 mm | 10 – 100 |
| Lifting Eye Base Height | 12 mm | 5 – 50 |
| Hard Point Width | 50 mm | 20 – 150 |
| Hard Point Thickness | 16 mm | 5 – 50 |
| Hard Point Height | 80 mm | 20 – 200 |
| Hard Point Hole Diameter | 15 mm | 3 – 50 |
| Crawler Length | 700 mm | 300 – 1500 |
| Crawler Diameter | 140 mm | 50 – 300 |
| Cam Housing Diameter | 70 mm | 20 – 200 |
| Cam Housing Height | 28 mm | 5 – 100 |
| Sensor Cage Outer Diameter | 170 mm | 50 – 300 |
| Sensor Cage Height | 80 mm | 20 – 250 |
| Sensor Cage Wall | 4 mm | 1 – 15 |
| Sensor Probe Count | 3 mm | 2 – 5 |
| Sensor Probe Diameter | 6 mm | 2 – 20 |
| Sensor Probe Length | 70 mm | 20 – 200 |
| Foam Collar Outer Diameter | 190 mm | 60 – 400 |
| Foam Collar Inner Diameter | 145 mm | 20 – 350 |
| Foam Collar Length | 150 mm | 20 – 400 |
| Wire Channel Diameter | 10 mm | 2 – 30 |
| Wire Channel Length | 900 mm | 100 – 3000 |
| Downweight Diameter | 130 mm | 40 – 350 |
| Downweight Total Height | 180 mm | 40 – 500 |
| Downweight Disc Count | 4 mm | 1 – 10 |
| Downweight Disc Gap | 6 mm | 0 – 30 |
| Bumper Collar Diameter | 140 mm | 40 – 400 |
| Bumper Collar Height | 35 mm | 5 – 80 |
Every value above is a live dimension. Open a model like this in the editor and each one becomes a slider you can drag before exporting.
More models
Browse the full gallery →Cylindrical Stainless Steel Basket with Folding Handles
Design a cylindrical 304 stainless steel basket with an outer diameter of 200 mm and height of 250 mm. The basket has solid side walls with no perforations. The bottom plate contai
Trumpet Lyre Mount Main Body
A single 3D mechanical CAD part for a trumpet music lyre mount (Main Body with Paddle). Geometry details: 1. A 18mm-wide semi-cylindrical clamp arc for a 28mm diameter cylinder, w
Spur Gearbox
design gearbox