Brackets and mounts
Portable Motorcycle Recovery Assist — Concept Design
- Bounding box
- 1086.5 × 515 × 790.2 mm
- Engine
- 3D Printing B-rep
- Parameters
- 51
- Published
- November 15, 2026
Download
Free to download and use. See the terms.
The prompt
> Create a realistic industrial-design 3D concept board of a portable motorcycle recovery-assist device, using the attached model as reference. Preserve its dark rectangular braced base, four feet, central pivot, and inclined silver telescopic arm. > > Add fold-out stabilizers with adjustable swivelling rubber pads; a manual telescopic screw actuator with fold-out crank; and a pivoting padded attachment head secured by a captive pin to a proposed structural motorcycle recovery bracket—not fairings, handlebars, or exhaust. Show a separate toothed holding rail with a spring-loaded pawl and guarded orange release lever. > > Include a folded-storage configuration with the arm retracted, stabilizers and crank folded inward, carrying handle, and transport latch. Keep all parts and geometry consistent across views. > > Show front, side, top, large isometric, folded-storage, and actuator-cutaway views. Include close-ups of the attachment head and holding lock. > > Along the bottom, show the same unbranded black-and-red sport motorcycle in three stages: “Initial attachment”, “Partial lift”, and “Held handover position”. Show the bike rotating toward upright, not lifting vertically. In the final panel, keep both tyres on the ground and mark the motorcycle centreline approximately 45° above horizontal: “Illustrative 45° handover position”. Do not confuse this with the actuator angle or imply a guaranteed safe handover. > > Use matte charcoal framing, brushed silver actuator parts, orange controls, dark rubber pads, a light-grey background, soft studio lighting, and clear engineering callouts. Show the lead screw and travelling nut in the cutaway; do not add hydraulics or gas struts. > > Title: “Portable Motorcycle Recovery Assist — Concept Design”. > > Footer: “Concept visualization — geometry, strength, stability and attachment compatibility require engineering validation.” > > No floating parts, impossible joints, changing geometry, invented load ratings, universal-fit claims, certification marks, patent claims, people, logos, or watermark.
Parameters
| Name | Value | Range |
|---|---|---|
| A-frame width | 520 mm | 300 – 700 |
| A-frame length | 420 mm | 300 – 600 |
| A-frame height | 140 mm | 100 – 220 |
| Frame tube diameter | 24 mm | 16 – 40 |
| Rubber foot width | 60 mm | 40 – 90 |
| Rubber foot depth | 40 mm | 25 – 60 |
| Rubber foot height | 20 mm | 10 – 30 |
| Retracted arm length | 480 mm | 300 – 600 |
| Extension beyond retracted | 370 mm | 0 – 370 |
| Outer tube diameter | 50 mm | 30 – 70 |
| Inner tube diameter | 40 mm | 20 – 60 |
| Deployed lift angle | 45 deg | 20 – 60 |
| Actuator diameter | 30 mm | 15 – 45 |
| Actuator stroke | 600 mm | 300 – 700 |
| Actuator offset from centreline | 35 mm | 20 – 70 |
| Internal lead screw diameter | 12 mm | 6 – 20 |
| Travelling nut diameter | 20 mm | 10 – 30 |
| Clamp width | 120 mm | 80 – 200 |
| Clamp depth | 80 mm | 50 – 120 |
| Clamp height | 60 mm | 40 – 100 |
| Cradle pivot angle | 10 deg | 0 – 30 |
| Strap width | 50 mm | 25 – 75 |
| Strap thickness | 2 mm | 1 – 4 |
| Strap length | 1500 mm | 800 – 2000 |
| Stabilizer arm length | 180 mm | 100 – 250 |
| Stabilizer arm width | 24 mm | 16 – 40 |
| Stabilizer arm height | 12 mm | 8 – 20 |
| Swivel pad diameter | 70 mm | 50 – 90 |
| Swivel pad height | 20 mm | 10 – 30 |
| Crank arm length | 80 mm | 50 – 120 |
| Crank handle length | 30 mm | 20 – 40 |
| Crank rod diameter | 12 mm | 8 – 20 |
| Holding rail length | 340 mm | 200 – 500 |
| Rail width | 16 mm | 10 – 30 |
| Rail thickness | 8 mm | 5 – 15 |
| Tooth pitch | 12 mm | 8 – 25 |
| Pawl width | 20 mm | 12 – 30 |
| Pawl height | 16 mm | 10 – 30 |
| Pivot pin diameter | 20 mm | 10 – 30 |
| Pivot pin length | 60 mm | 30 – 100 |
| Hinge width | 80 mm | 50 – 120 |
| Hinge depth | 50 mm | 30 – 80 |
| Hinge height | 30 mm | 15 – 50 |
| Safety stop width | 40 mm | 20 – 60 |
| Safety stop depth | 25 mm | 15 – 40 |
| Safety stop height | 20 mm | 10 – 35 |
| Ratchet width | 180 mm | 80 – 250 |
| Ratchet depth | 80 mm | 40 – 120 |
| Ratchet height | 40 mm | 20 – 70 |
| Carrying handle width | 200 mm | 120 – 300 |
| Carrying handle diameter | 14 mm | 8 – 24 |
Every value above is a live dimension. Open a model like this in the editor and each one becomes a slider you can drag before exporting.
More models
Browse the full gallery →UAV Ogive Nose Cone
Design a watertight, 3D-printable aerodynamic nose cone module for a fixed-wing tactical UAV, optimized for printing in Carbon Fiber Filled PETG (PETG-CF). The base of the nose con
Trumpet Lyre Mount Main Body
A single 3D mechanical CAD part for a trumpet music lyre mount (Main Body with Paddle). Geometry details: 1. A 18mm-wide semi-cylindrical clamp arc for a 28mm diameter cylinder, w
Flat-Strap Reel Spool
Create a 3D model of a custom flat-strap reel spool for a home plate housing cavity. Geometry: - A reel spool consisting of two parallel circular outer flanges connected by a cent
PET Recycling Kiosk Frame
Design a production-ready welded steel frame for an outdoor PET bottle recycling and animal feeding kiosk. Create ONLY the steel frame. Do not create covers, motors, tanks, electr
JZX100 Gas Cap Holder
can you make a gas cap holder for a jzx100 chaser. i want you to refer to the image and make a cad very close to the picture
Compression Testing Tower
The central square tower contains a 450 mm lead screw and a parallel 16 mm diameter steel guide shaft. Both are securely supported by bearings. A horizontal sliding block spans be
