Enclosures and housings
Pocket Utility Knife (Stanley 1992) - Handle + Blade Carrier
- Bounding box
- 100.0 × 28.0 × 11.4 mm
- Engine
- Precision B-rep
- Parameters
- 38
- Published
- November 5, 2026
Download
Free to download and use. See the terms.
The prompt
2-piece aluminum pocket utility knife handle for Stanley 1992 blades, CNC-optimized, 100x28x10 mm, thumb slide slot 4 mm with 3 detents, engraved 2 in scale with 1/16 in ticks, four M3 countersunk screws. Revised: added blade carrier that holds the blade by its back-edge notches, spring-arm detents, wider screw spacing.
Parameters
| Name | Value | Range |
|---|---|---|
| Handle length | 100 mm | 90 – 120 |
| Handle width | 28 mm | 24 – 34 |
| Assembled thickness | 10 mm | 8 – 14 |
| Corner radius | 3 mm | 1 – 6 |
| Outer edge chamfer | 0.4 mm | 0 – 1 |
| Blade length (1992) | 62 mm | 55 – 70 |
| Blade width (1992) | 19 mm | 17 – 21 |
| Blade thickness | 0.65 mm | 0.5 – 0.8 |
| Pocket side clearance | 0.4 mm | 0.1 – 1 |
| Blade protrusion when extended | 20 mm | 18 – 24 |
| Pocket floor depth (back plate) | 0.4 mm | 0.2 – 0.8 |
| Carrier thickness | 1.2 mm | 0.8 – 2 |
| Carrier length | 40 mm | 34 – 42 |
| Blade notch spacing (verify on blade) | 12 mm | 8 – 16 |
| Carrier pin dia | 2 mm | 1.4 – 2.4 |
| Thumb post dia | 3.6 mm | 3 – 4.4 |
| Thumb cap dia | 8 mm | 6 – 12 |
| Slide travel | 25 mm | 10 – 26 |
| Thumb slot width | 4 mm | 3.5 – 6 |
| Detent dimple radius | 0.9 mm | 0.6 – 1.5 |
| Detent dimple depth | 0.45 mm | 0.2 – 0.8 |
| Spring-arm bump height | 0.35 mm | 0.2 – 0.6 |
| First screw column X | 7 mm | 5.5 – 14 |
| Screw column spacing | 20 mm | 10 – 21 |
| Screw offset from centerline | 10 mm | 5 – 10.5 |
| Clearance hole dia | 3.4 mm | 3.2 – 3.6 |
| Countersink dia (90 deg) | 6.3 mm | 5.5 – 7 |
| Tap drill dia (back plate) | 2.5 mm | 2.4 – 2.6 |
| Tap drill depth | 4 mm | 3 – 4.5 |
| Scale start X | 36 mm | 30 – 45 |
| Scale baseline Y | -13 mm | -13.4 – -11 |
| Tick line width | 0.25 mm | 0.15 – 0.5 |
| Engrave depth | 0.2 mm | 0.1 – 0.4 |
| Inch tick length | 3.5 mm | 2 – 4 |
| 1/2 in tick length | 3 mm | 1.5 – 4 |
| 1/4 in tick length | 2.4 mm | 1.2 – 4 |
| 1/8 in tick length | 1.8 mm | 1 – 4 |
| 1/16 in tick length | 1.2 mm | 0.6 – 4 |
Every value above is a live dimension. Open a model like this in the editor and each one becomes a slider you can drag before exporting.
More models
Browse the full gallery →Cylindrical Stainless Steel Basket with Folding Handles
Design a cylindrical 304 stainless steel basket with an outer diameter of 200 mm and height of 250 mm. The basket has solid side walls with no perforations. The bottom plate contai
Immersion Cooling Enclosure
Design a sealed high-pressure dielectric immersion cooling enclosure for cylindrical battery cells. Internal cavity dimensions: 540mm length, 360mm width, 160mm height with 6mm wal
Simple BWB with Propulsion Tube
Prompt: "A simple, solid Blended Wing Body (BWB) flying wing. Dimensions: wingspan 6.5 meters, center chord 1.53 meters, root thickness 35 centimeters, tapering to 15 centimeters a
Engranaje recto 50 dientes, módulo 2
Engranaje recto de 50 dientes, diámetro exterior 104 mm, diámetro de raíz 95 mm, espesor 10 mm y ángulo de presión 20°. Crear como sólido 3D con un agujero central de 8.2 mm de diá
G+1 Party Hall Structural Shell
G+1 Party Hall – AutoCAD Design Prompt Design a G+1 RCC-framed Party Hall in AutoCAD with detailed Ground Floor Plan, First Floor Plan, and all-side elevations (front, rear, left
Default Spur Gear
La costruzione dovrà prevedere i seguenti spazi: 1. Zona Giorno (Piano Terra)-Totale:~110 mg • Ingresso / Disimpegno con guardaroba: 10 mg • Soggiorno / Area Living: 40 mq (ampio,