Enclosures and housings
Plywood Attaché Case — Prototype Enclosure
- Bounding box
- 457.0 × 384.0 × 127.0 mm
- Engine
- Precision B-rep
- Parameters
- 38
- Published
- October 8, 2026
Download
Free to download and use. See the terms.
The prompt
Revise the existing 450 x 350 x 120 mm plywood attaché case so it matches the built prototype. Keep the size: base height 80 mm, lid height 40 mm, plywood 8 mm. Closed: light plywood box, black plastic handle centered on the front face, two small metal latches on the right side edge, visible seam between lid and base. Open: lid rotated 105 degrees on the rear hinge. Inner lid is darker reddish plywood. A 10.1 inch dark screen sits left of center. A small camera hole is immediately to the right of the screen. A small round fan grille is further right, lower than the camera. Metal corner plates on the top corners of the lid. Two thin metal stays, one on each side, holding the lid open. Base is empty with a light grey wood-grain floor liner. Black handle remains on the front wall. One small metal latch plate on the front inner lip. Show the open configuration. Do not change overall size.
Parameters
| Name | Value | Range |
|---|---|---|
| Overall Width (X) | 450 mm | 300 – 700 |
| Overall Depth (Y) | 350 mm | 250 – 550 |
| Plywood Thickness | 8 mm | 4 – 18 |
| Base Outer Height | 80 mm | 40 – 150 |
| Lid Outer Height | 40 mm | 20 – 120 |
| Lid/Base Seam Reveal | 1.2 mm | 0 – 3 |
| Floor Liner Thickness | 1 mm | 0.2 – 3 |
| Screen Centre Y | 175 mm | 60 – 290 |
| Screen Module Width | 235 mm | 100 – 400 |
| Screen Module Height | 145 mm | 60 – 300 |
| Screen Mount Depth | 8 mm | 2 – 20 |
| Screen Centre X | -60 mm | -180 – 180 |
| Camera Hole Dia | 9 mm | 4 – 30 |
| Camera Centre X | 75 mm | -180 – 200 |
| Fan Opening Dia | 40 mm | 20 – 90 |
| Fan Centre X | 140 mm | -180 – 200 |
| Fan Offset Down from Camera | 25 mm | -60 – 80 |
| Grille Bar Width | 4 mm | 1.5 – 10 |
| Corner Plate Size | 40 mm | 15 – 90 |
| Corner Plate Thickness | 2 mm | 0.5 – 5 |
| Hinge Knuckle Width | 30 mm | 15 – 60 |
| Hinge Leaf Length | 40 mm | 20 – 90 |
| Lid Stay Width | 10 mm | 5 – 30 |
| Lid Stay Thickness | 2 mm | 1 – 6 |
| Latch Spacing (right edge) | 200 mm | 60 – 320 |
| Latch Plate Length | 40 mm | 15 – 90 |
| Latch Plate Thickness | 3 mm | 1 – 8 |
| Latch Plate Height | 20 mm | 8 – 45 |
| Front Lip Plate Width | 30 mm | 10 – 120 |
| Front Lip Plate Height | 14 mm | 5 – 45 |
| Front Lip Plate Thickness | 2 mm | 0.5 – 6 |
| Handle Grip Span | 130 mm | 60 – 260 |
| Handle Stand-off | 20 mm | 8 – 50 |
| Handle Height on Wall | 40 mm | 15 – 70 |
| Grip Bar Radius | 8 mm | 3 – 18 |
| Foot Diameter | 15 mm | 8 – 40 |
| Foot Thickness | 5 mm | 2 – 15 |
| Foot Inset from Corner | 20 mm | 5 – 80 |
Every value above is a live dimension. Open a model like this in the editor and each one becomes a slider you can drag before exporting.
More models
Browse the full gallery →Cylindrical Stainless Steel Basket with Folding Handles
Design a cylindrical 304 stainless steel basket with an outer diameter of 200 mm and height of 250 mm. The basket has solid side walls with no perforations. The bottom plate contai
Immersion Cooling Enclosure
Design a sealed high-pressure dielectric immersion cooling enclosure for cylindrical battery cells. Internal cavity dimensions: 540mm length, 360mm width, 160mm height with 6mm wal
Simple BWB with Propulsion Tube
Prompt: "A simple, solid Blended Wing Body (BWB) flying wing. Dimensions: wingspan 6.5 meters, center chord 1.53 meters, root thickness 35 centimeters, tapering to 15 centimeters a
Engranaje recto 50 dientes, módulo 2
Engranaje recto de 50 dientes, diámetro exterior 104 mm, diámetro de raíz 95 mm, espesor 10 mm y ángulo de presión 20°. Crear como sólido 3D con un agujero central de 8.2 mm de diá
G+1 Party Hall Structural Shell
G+1 Party Hall – AutoCAD Design Prompt Design a G+1 RCC-framed Party Hall in AutoCAD with detailed Ground Floor Plan, First Floor Plan, and all-side elevations (front, rear, left
Rope Winch Drum
Create a fully parametric CAD model of a rope winch drum for a construction hoist. Requirements: - Output format: STEP (.step or .stp) - Units: millimeters - Solid body only (no