Brackets and mounts
NACA 0012 Wing with Free-Spinning Cylinder and Adjustable AoA Hinge
- Bounding box
- 40.0 × 408.0 × 21.4 mm
- Engine
- Precision B-rep
- Parameters
- 40
- Published
- November 15, 2026
Download
Free to download and use. See the terms.
The prompt
Create a 3D CAD assembly of a NACA 0012 airfoil with a passive free-spinning cylinder and adjustable angle of attack. All dimensions are in mm. **1. Modified airfoil** - NACA 0012 symmetrical profile. - Chord: 40 mm; span: 200 mm; maximum thickness: 4.801 mm. - Spanwise cylindrical cavity: Ø6.3 × 200 mm. - Cavity center: 11.993 mm from leading edge and 1.901 mm above chord line. - Material: PLA. **2. Rotating cylinder** - Diameter: 5 mm; length: 200 mm. - Radial clearance: 0.65 mm. - 60% embedded and 40% exposed. - Two concentric holes at the cylinder ends for steel journals. - Two steel journals: Ø3 × 6 mm. - No continuous shaft. - Material: PLA. **3. Bearings (2)** - MR63 miniature ball bearings. - ID: 3 mm; OD: 6 mm; width: 2 mm. - One bearing at each cylinder end. **4. Bearing supports (2)** - Rectangular PLA blocks: 12 × 8 × 4 mm. - Bearing recess: Ø6 mm, 2 mm deep. - Journal clearance hole: Ø4 mm. - Attach externally to both wingtips. - Align concentrically with the cylinder and allow unrestricted rotation. **5. Angle-of-attack adjustment** - Two simple mating brackets connected by an M3 bolt, nut and washers. - Upper bracket matches the curved underside of the airfoil. - Lower bracket has a flat mounting base. - Pivot holes: Ø3.2 mm. - Position at midspan and 10 mm from the leading edge. - Spanwise pivot axis with 0–25° angular adjustment. - Loosen bolt to adjust angle and tighten to lock. Generate separate solid parts, a complete assembly, and STEP files compatible with Autodesk Inventor. Check interference and rotational clearances. Colors: gray airfoil, red cylinder, dark gray brackets and bearing supports, metallic bearings and fasteners. Exclude the wind tunnel, clean airfoil, vertical support, force platform, load cell and cylinder locking mechanism.
Parameters
| Name | Value | Range |
|---|---|---|
| Chord | 40 mm | 20 – 120 |
| Span | 200 mm | 60 – 400 |
| Thickness Ratio (NACA 0012 = 0.12) | 0.12 ratio | 0.06 – 0.2 |
| Spanwise Cavity Dia | 6.3 mm | 4 – 12 |
| Cavity Centre from LE | 11.99 mm | 3 – 30 |
| Cavity Centre above Chord Line | 1.9 mm | 0 – 10 |
| Rotating Cylinder Dia | 5 mm | 2 – 10 |
| Rotating Cylinder Length | 200 mm | 60 – 400 |
| Bearing Bore (ID) | 3 mm | 1 – 8 |
| Bearing Outer Dia | 6 mm | 3 – 16 |
| Bearing Width | 2 mm | 1 – 8 |
| Journal Dia | 3 mm | 1 – 8 |
| Journal Length | 6 mm | 4 – 20 |
| Support Block Width (X) | 12 mm | 8 – 30 |
| Support Block Height (Z) | 8 mm | 6 – 25 |
| Support Block Thickness (Y) | 4 mm | 3 – 15 |
| Bearing Recess Dia | 6 mm | 3 – 16 |
| Bearing Recess Depth | 2 mm | 1 – 8 |
| Journal Clearance Hole Dia | 4 mm | 3.2 – 10 |
| Pivot Hole Dia | 3.2 mm | 2 – 8 |
| Pivot Distance from LE | 10 mm | 2 – 40 |
| Pivot Axis Below Chord Line | -6.5 mm | -25 – -3 |
| Lug Thickness (Y) | 4 mm | 2 – 12 |
| Upper Bracket Chordwise Length | 10 mm | 6 – 30 |
| Upper Bracket Drop below Pivot | 2.5 mm | 0.5 – 10 |
| Lower Base Length (X) | 20 mm | 10 – 60 |
| Lower Base Width (Y) | 10 mm | 6 – 30 |
| Lower Base Thickness | 3 mm | 1.5 – 10 |
| Base Top below Pivot | 6 mm | 2 – 20 |
| Lower Lug Width (X) | 4 mm | 2 – 12 |
| Lug Top above Pivot | 2.5 mm | 0.5 – 10 |
| Bolt Shank Dia (M3) | 3 mm | 2 – 6 |
| Bolt Head Dia | 5.5 mm | 3 – 12 |
| Bolt Head Height | 3 mm | 1 – 8 |
| Bolt Shank Length | 12.5 mm | 6 – 30 |
| Nut Across Flats (M3) | 5.5 mm | 3 – 12 |
| Nut Height | 2.4 mm | 1 – 8 |
| Washer Outer Dia | 7 mm | 3.5 – 16 |
| Washer Bore | 3.2 mm | 2 – 8 |
| Washer Thickness | 0.5 mm | 0.2 – 3 |
Every value above is a live dimension. Open a model like this in the editor and each one becomes a slider you can drag before exporting.
More models
Browse the full gallery →UAV Ogive Nose Cone
Design a watertight, 3D-printable aerodynamic nose cone module for a fixed-wing tactical UAV, optimized for printing in Carbon Fiber Filled PETG (PETG-CF). The base of the nose con
Trumpet Lyre Mount Main Body
A single 3D mechanical CAD part for a trumpet music lyre mount (Main Body with Paddle). Geometry details: 1. A 18mm-wide semi-cylindrical clamp arc for a 28mm diameter cylinder, w
Flat-Strap Reel Spool
Create a 3D model of a custom flat-strap reel spool for a home plate housing cavity. Geometry: - A reel spool consisting of two parallel circular outer flanges connected by a cent
PET Recycling Kiosk Frame
Design a production-ready welded steel frame for an outdoor PET bottle recycling and animal feeding kiosk. Create ONLY the steel frame. Do not create covers, motors, tanks, electr
JZX100 Gas Cap Holder
can you make a gas cap holder for a jzx100 chaser. i want you to refer to the image and make a cad very close to the picture
Compression Testing Tower
The central square tower contains a 450 mm lead screw and a parallel 16 mm diameter steel guide shaft. Both are securely supported by bearings. A horizontal sliding block spans be
