Brackets and mounts
NACA 0012 Airfoil with Passive Cylinder and Angle Wedges
- Bounding box
- 40.1 × 323.0 × 23.9 mm
- Engine
- Precision B-rep
- Parameters
- 24
- Published
- November 15, 2026
Download
Free to download and use. See the terms.
The prompt
Modify the existing assembly. Retain these 8 existing parts without changing their geometry: - Airfoil - Rotating cylinder - Journal top - Journal bottom - Bearing top - Bearing bottom - Bearing support top - Bearing support bottom Remove these 6 parts: - Upper bracket - Lower bracket - Bolt - Nut - Washer a - Washer b Replace the hinge mechanism with six independent mounting wedges at 0°, 5°, 10°, 12°, 14° and 15°. Each wedge must have a chordwise length of 20 mm, spanwise width of 15 mm, minimum thickness of 3 mm, flat bottom and a contoured upper surface matching the underside of the NACA 0012 airfoil. Positive angles must raise the leading edge. Generate each wedge as a separate PLA solid part, labeled with its angle. Do not attach any wedges to the airfoil or assemble them together. Each wedge must be individually exportable. Preserve all other existing components.
Parameters
| Name | Value | Range |
|---|---|---|
| Chord | 40 mm | 10 – 200 |
| Span | 200 mm | 20 – 400 |
| Thickness ratio | 0.12 mm | 0.04 – 0.2 |
| Cavity diameter | 6.3 mm | 2 – 20 |
| Cavity center X | 11.99 mm | 0 – 40 |
| Cavity center Z | 1.9 mm | -5 – 5 |
| Cylinder diameter | 5 mm | 1 – 20 |
| Cylinder length | 200 mm | 20 – 400 |
| Journal diameter | 3 mm | 1 – 10 |
| Journal length | 6 mm | 2 – 20 |
| Bearing ID | 3 mm | 1 – 10 |
| Bearing OD | 6 mm | 2 – 20 |
| Bearing width | 2 mm | 0.5 – 5 |
| Support width | 12 mm | 5 – 50 |
| Support height | 8 mm | 4 – 40 |
| Support thickness | 4 mm | 1 – 10 |
| Recess diameter | 6 mm | 3 – 20 |
| Recess depth | 2 mm | 1 – 10 |
| Clearance hole diameter | 4 mm | 2 – 20 |
| Wedge chord length | 20 mm | 5 – 40 |
| Wedge spanwise width | 15 mm | 5 – 50 |
| Wedge min thickness | 3 mm | 0.5 – 10 |
| Wedge start X | 0 mm | 0 – 40 |
| Wedge gap | 0 mm | 0 – 20 |
Every value above is a live dimension. Open a model like this in the editor and each one becomes a slider you can drag before exporting.
More models
Browse the full gallery →UAV Ogive Nose Cone
Design a watertight, 3D-printable aerodynamic nose cone module for a fixed-wing tactical UAV, optimized for printing in Carbon Fiber Filled PETG (PETG-CF). The base of the nose con
Trumpet Lyre Mount Main Body
A single 3D mechanical CAD part for a trumpet music lyre mount (Main Body with Paddle). Geometry details: 1. A 18mm-wide semi-cylindrical clamp arc for a 28mm diameter cylinder, w
Flat-Strap Reel Spool
Create a 3D model of a custom flat-strap reel spool for a home plate housing cavity. Geometry: - A reel spool consisting of two parallel circular outer flanges connected by a cent
PET Recycling Kiosk Frame
Design a production-ready welded steel frame for an outdoor PET bottle recycling and animal feeding kiosk. Create ONLY the steel frame. Do not create covers, motors, tanks, electr
JZX100 Gas Cap Holder
can you make a gas cap holder for a jzx100 chaser. i want you to refer to the image and make a cad very close to the picture
Compression Testing Tower
The central square tower contains a 450 mm lead screw and a parallel 16 mm diameter steel guide shaft. Both are securely supported by bearings. A horizontal sliding block spans be
