Brackets and mounts
Modular Desoldering Jig — 900M Iron + BDM-010 Cartridge
- Bounding box
- 200.0 × 140.0 × 268.0 mm
- Engine
- Precision B-rep
- Parameters
- 60
- Published
- November 19, 2026
Download
Free to download and use. See the terms.
The prompt
Create a complete, modular 3D-printable mechanical desoldering jig assembly for game controller motherboards (starting with a PS5 DualSense BDM-010 cartridge), designed around a vertical 90W 900M soldering iron (total height 245 mm including right-angle power cable bend) fitted with a 19 mm x 23 mm upward-facing brass joystick desoldering tip. Design the model as 3 clean, printable parametric sub-parts with adjustable parameters (sliders): 1. UNIVERSAL BASE & COLUMNS: - Heavy rectangular base plate: 200 mm length (X) x 140 mm width (Y) x 12 mm thickness (Z). - Two parallel horizontal guide rails along the X-axis (8 mm diameter shafts, 160 mm long, spaced 50 mm apart in Y) mounted on end blocks, allowing at least 80 mm of smooth left-to-right travel for left/right joystick alignment. - Four vertical corner support columns rising from the four corners of the base to place the top mounting surface at exactly 260 mm total height above the base floor (245 mm soldering iron height + 15 mm vertical clearance stroke). - On the top face of each of the 4 columns, add a 6 mm diameter x 4 mm tall cylindrical alignment boss and a recess for an 8 mm x 3 mm magnet to lock interchangeable top plates. 2. SLIDING SOLDERING IRON CARRIAGE (900M 90W): - Central carriage block mounted on the two 8 mm horizontal rails with two mechanical stop notches along X (spaced 52 mm apart by default, adjustable via slider for left and right joystick centers). - Vertical split clamp collar in the center (adjustable inner diameter, default 22 mm, with a side tightening screw tab) positioned to grip the insulated handle of the 900M soldering iron vertically from below, leaving clear passage at the bottom for the power cord bent at 90 degrees. - Vertical travel clearance of 15 mm so the 19 mm x 23 mm brass tip can rise straight up to contact the PCB solder pins from underneath. 3. INTERCHANGEABLE TOP PCB CARTRIDGE PLATE (BDM-010 DEFAULT): - Removable rectangular top plate: 200 mm length x 140 mm width x 6 mm thickness, with four 6.2 mm corner alignment holes matching the 4 column bosses so plates can be swapped quickly for PS4, PS5, Xbox, or future PS6 boards. - In the exact center, design a recessed PCB cradle zone sized for a 71 mm x 55 mm motherboard footprint (make pcb_length = 71 mm, pcb_width = 55 mm, and pcb_thickness = 1.6 mm adjustable via parameters, with 7 mm component clearance around the edges). - Cut a wide central rectangular pass-through window (90 mm wide in X x 36 mm deep in Y) directly under the joystick zone so the 19 mm x 23 mm brass desoldering head passes cleanly from underneath without touching any plastic. - Add four 2.0 mm diameter x 4 mm tall vertical indexing pins positioned at the perimeter of the PCB cradle (X and Y spacing adjustable via sliders) to locate the motherboard using its original chassis screw holes. Keep all geometries clean, solid, manifold, with flat bottom faces suitable for FDM 3D printing and export to STEP/STL.
Parameters
| Name | Value | Range |
|---|---|---|
| Base Length | 200 mm | 120 – 320 |
| Base Width | 140 mm | 80 – 240 |
| Base Thickness | 12 mm | 4 – 30 |
| Top Mounting Surface Height | 260 mm | 180 – 400 |
| Column Cross-Section | 22 mm | 10 – 40 |
| Column Edge Margin | 3 mm | 0 – 20 |
| Alignment Boss Diameter | 6 mm | 3 – 12 |
| Alignment Boss Height | 4 mm | 1 – 10 |
| Magnet Diameter | 8 mm | 4 – 16 |
| Magnet Thickness | 3 mm | 1 – 8 |
| Column Magnet Pocket Depth | 1.8 mm | 0.5 – 6 |
| Magnet Offset From Column Centre | 6 mm | 2 – 10 |
| End Block Length (X) | 20 mm | 10 – 40 |
| End Block Width (Y) | 80 mm | 30 – 140 |
| End Block Height | 40 mm | 15 – 80 |
| End Block Inset From Base End | 8 mm | 0 – 30 |
| Guide Rail Diameter | 8 mm | 4 – 16 |
| Guide Rail Length | 160 mm | 80 – 260 |
| Rail Spacing (Y) | 50 mm | 20 – 120 |
| Rail Axis Height | 42 mm | 15 – 120 |
| Carriage Length (X) | 60 mm | 30 – 120 |
| Carriage Width (Y) | 72 mm | 40 – 140 |
| Carriage Height | 24 mm | 12 – 60 |
| Carriage Bottom Below Rail Axis | 12 mm | 6 – 30 |
| Stop Notch Spacing | 52 mm | 20 – 120 |
| Stop Notch Width | 4 mm | 1 – 12 |
| Stop Notch Length (Y) | 14 mm | 4 – 40 |
| Stop Notch Depth | 4 mm | 1 – 10 |
| Clamp Inner Diameter | 22 mm | 12 – 40 |
| Clamp Outer Diameter | 46 mm | 24 – 80 |
| Clamp Height | 26 mm | 10 – 60 |
| Clamp Slit Width | 3 mm | 1 – 10 |
| Screw Tab Length | 10 mm | 4 – 30 |
| Screw Tab Width | 8 mm | 4 – 24 |
| Clamp Screw Clearance | 3.2 mm | 2 – 8 |
| Iron Handle Diameter | 22 mm | 10 – 40 |
| Iron Handle Length | 170 mm | 80 – 250 |
| Iron Barrel Diameter | 8 mm | 3 – 20 |
| Iron Barrel Length | 34 mm | 10 – 120 |
| Brass Tip Width (X) | 19 mm | 8 – 40 |
| Brass Tip Depth (Y) | 23 mm | 8 – 40 |
| Brass Tip Height | 17 mm | 5 – 60 |
| Iron Tip Top Height | 245 mm | 150 – 380 |
| Power Cord Diameter | 8 mm | 3 – 16 |
| Power Cord Bend Length | 55 mm | 20 – 120 |
| Cartridge Plate Length | 200 mm | 120 – 320 |
| Cartridge Plate Width | 140 mm | 80 – 240 |
| Cartridge Plate Thickness | 6 mm | 2 – 20 |
| Corner Alignment Hole Dia | 6.2 mm | 3 – 16 |
| Pass-Through Window Length | 90 mm | 20 – 160 |
| Pass-Through Window Width | 36 mm | 10 – 100 |
| Motherboard Length | 71 mm | 20 – 160 |
| Motherboard Width | 55 mm | 20 – 120 |
| Motherboard Thickness | 1.6 mm | 0.6 – 4 |
| Component Clearance Around PCB | 7 mm | 0 – 20 |
| Cradle Recess Depth | 2 mm | 0.5 – 5 |
| Indexing Pin Diameter | 2 mm | 0.8 – 8 |
| Indexing Pin Height | 4 mm | 1 – 15 |
| Indexing Pin Spacing (X) | 65 mm | 20 – 150 |
| Indexing Pin Spacing (Y) | 49 mm | 10 – 100 |
Every value above is a live dimension. Open a model like this in the editor and each one becomes a slider you can drag before exporting.
More models
Browse the full gallery →UAV Ogive Nose Cone
Design a watertight, 3D-printable aerodynamic nose cone module for a fixed-wing tactical UAV, optimized for printing in Carbon Fiber Filled PETG (PETG-CF). The base of the nose con
Trumpet Lyre Mount Main Body
A single 3D mechanical CAD part for a trumpet music lyre mount (Main Body with Paddle). Geometry details: 1. A 18mm-wide semi-cylindrical clamp arc for a 28mm diameter cylinder, w
Flat-Strap Reel Spool
Create a 3D model of a custom flat-strap reel spool for a home plate housing cavity. Geometry: - A reel spool consisting of two parallel circular outer flanges connected by a cent
PET Recycling Kiosk Frame
Design a production-ready welded steel frame for an outdoor PET bottle recycling and animal feeding kiosk. Create ONLY the steel frame. Do not create covers, motors, tanks, electr
JZX100 Gas Cap Holder
can you make a gas cap holder for a jzx100 chaser. i want you to refer to the image and make a cad very close to the picture
Micro RC Airplane Frame
Create a lightweight 3D-printable indoor micro RC airplane frame. The fuselage is a hollow rectangular boom 200 mm long, 3 mm wide, and 3 mm tall, with an open U-shaped electronics
