Brackets and mounts
LPR Rocker-Bogie Rover (Exploded Assembly)
- Bounding box
- 14515.0 × 640.0 × 668.0 mm
- Engine
- Precision B-rep
- Parameters
- 50
- Published
- November 15, 2026
Download
Free to download and use. See the terms.
The prompt
designn A six-wheel rocker-bogie all-terrain rover with four-wheel steering, carrying a 6-DOF arm with a hybrid vacuum and soft-finger end-effector, and a rear collection hopper. The layout must stay modular so the same architecture can later scale to a heavy-duty tracked commercial unit. The mechanical design must have Climb 30° with 3 of 6 wheels loaded in the worst case Report Step 200 mm validated, 250 mm stretch Report / Proposed Ground clearance 240 mm under the skid plate Report Mass 65 kg design value, 75 kg hard cap Report / Proposed Speed 1.0 m/s maximum Report Hopper 35 to 40 L Proposed Runtime 3 hours per charge Report 2. Working rules • Software and units: SolidWorks, millimetres, kilograms, newtons. • Coordinate system (Proposed): origin on the ground plane beneath the rear axle centreline on the vehicle centreline; x forward, y left, z up. This matches the ROS convention the software team uses. • Master skeleton: build one layout sketch driven by the global parameters in section 3. Change parameters, not individual parts. • Purchased items: use vendor STEP files. Where none exists, model an envelope block named ENVELOPE - replace with vendor model. • Naming: LPR-subsystem-part-revision. • Mass: assign material and density to every part and report the mass roll-up and centre of gravity at every review gate. 3. Global parameters (drive these from the skeleton) Parameter Value Origin Wheel diameter 260 mm knobby pneumatic ATV tyre Report Tyre width 90 mm placeholder, confirm with supplier Proposed Wheelbase 800 mm Spec Rear axle x = 0 mm Spec Rocker chassis pivot x = 300 mm Spec Bogie pivot x = 610 mm Spec Middle axle x = 420 mm Spec Front axle x = 800 mm Spec Track, wheel centre to centre 620 mm placeholder; increase if steering clearance needs it Proposed Chassis tub 750 x 450 x 220 mm, 4040 aluminium T-slot extrusion Report Skid plate 3 mm 6061-T6 aluminium, 240 mm ground clearance Report Arm pedestal position 180 mm behind the front bumper Report Arm base height 500 mm (report layout), with a 400 mm option Report / Spec Hopper mouth about 330 to 650 mm behind the front bumper Spec Bogie travel ±35° with rubber bump-stops Report Steering lock ±35°
Parameters
| Name | Value | Range |
|---|---|---|
| Exploded Layout Gap | 1300 mm | 200 – 3000 |
| Tub Length X | 750 mm | 500 – 1200 |
| Tub Width Y | 450 mm | 300 – 800 |
| Tub Height Z | 220 mm | 150 – 400 |
| 4040 Extrusion Size | 40 mm | 20 – 60 |
| Skid Plate Thickness | 3 mm | 1 – 10 |
| Rolled Front Lip Height | 25 mm | 0 – 80 |
| Mounting Hole Dia | 8 mm | 3 – 16 |
| Rocker Pivot-to-Pivot | 430 mm | 250 – 700 |
| Rocker Beam Height | 60 mm | 30 – 120 |
| Rocker Plate Thickness | 6 mm | 3 – 16 |
| Rocker Pivot Bore | 16 mm | 6 – 30 |
| Rocker Pivot Boss Dia | 44 mm | 20 – 80 |
| Bogie Beam Length | 350 mm | 200 – 600 |
| Bogie Beam Height | 40 mm | 20 – 100 |
| Bogie Plate Thickness | 5 mm | 3 – 16 |
| Bogie Pivot Bore | 14 mm | 6 – 30 |
| Tyre Outer Diameter | 260 mm | 150 – 400 |
| Tyre Width | 90 mm | 40 – 160 |
| Rim Seat Diameter | 200 mm | 100 – 320 |
| Hub Adapter Diameter | 100 mm | 50 – 160 |
| Steering Actuator Dia | 80 mm | 50 – 140 |
| Steering Actuator Length | 60 mm | 30 – 120 |
| Knuckle Arm Length | 100 mm | 60 – 200 |
| Hub Flange Diameter | 60 mm | 30 – 120 |
| Gearmotor Envelope Size | 90 mm | 50 – 150 |
| Gearmotor Axial Length | 120 mm | 60 – 220 |
| Pedestal Column Size | 200 mm | 120 – 320 |
| Pedestal Column Height | 500 mm | 300 – 800 |
| Pedestal Wall Thickness | 8 mm | 2 – 20 |
| Base Flange Size | 240 mm | 150 – 400 |
| Base Flange Thickness | 8 mm | 4 – 30 |
| Rotate Bearing Dia | 180 mm | 80 – 300 |
| Rotate Bearing Height | 25 mm | 10 – 80 |
| Shoulder Link Length | 400 mm | 200 – 600 |
| Elbow Link Length | 350 mm | 150 – 550 |
| Forearm Link Length | 250 mm | 100 – 450 |
| Wrist Link Length | 120 mm | 60 – 250 |
| Link Section Width | 80 mm | 40 – 150 |
| Joint Module Dia | 80 mm | 40 – 140 |
| Gripper Body Dia | 90 mm | 50 – 160 |
| Gripper Body Length | 90 mm | 50 – 200 |
| Vacuum Cup Array Dia | 120 mm | 60 – 220 |
| Vacuum Cup Dia | 40 mm | 15 – 90 |
| Air Line Port Dia | 6 mm | 2 – 16 |
| Hopper Length X | 400 mm | 200 – 700 |
| Hopper Width Y | 350 mm | 200 – 600 |
| Hopper Height Z | 280 mm | 120 – 500 |
| Hopper Sheet Thickness | 2 mm | 1 – 8 |
| Folded Rim Width | 15 mm | 0 – 60 |
Every value above is a live dimension. Open a model like this in the editor and each one becomes a slider you can drag before exporting.
More models
Browse the full gallery →UAV Ogive Nose Cone
Design a watertight, 3D-printable aerodynamic nose cone module for a fixed-wing tactical UAV, optimized for printing in Carbon Fiber Filled PETG (PETG-CF). The base of the nose con
Trumpet Lyre Mount Main Body
A single 3D mechanical CAD part for a trumpet music lyre mount (Main Body with Paddle). Geometry details: 1. A 18mm-wide semi-cylindrical clamp arc for a 28mm diameter cylinder, w
Flat-Strap Reel Spool
Create a 3D model of a custom flat-strap reel spool for a home plate housing cavity. Geometry: - A reel spool consisting of two parallel circular outer flanges connected by a cent
PET Recycling Kiosk Frame
Design a production-ready welded steel frame for an outdoor PET bottle recycling and animal feeding kiosk. Create ONLY the steel frame. Do not create covers, motors, tanks, electr
JZX100 Gas Cap Holder
can you make a gas cap holder for a jzx100 chaser. i want you to refer to the image and make a cad very close to the picture
Compression Testing Tower
The central square tower contains a 450 mm lead screw and a parallel 16 mm diameter steel guide shaft. Both are securely supported by bearings. A horizontal sliding block spans be
