Brackets and mounts
LiPo Electronics Enclosure Base
- Bounding box
- 91 × 55 × 18 mm
- Engine
- 3D Printing B-rep
- Parameters
- 19
- Published
- November 18, 2026
Download
Free to download and use. See the terms.
The prompt
Create a rectangular electronics enclosure bottom base with outer dimensions 91 mm length, 55 mm width, and 18 mm height. Add 2 mm outer corner fillets on the vertical edges. Hollow out the inside with a 2 mm wall thickness and a 2 mm bottom floor thickness, leaving an open top cavity of 87 mm by 51 mm and 16 mm depth to hold a flat LiPo battery and a charging module. Inside the four corners, add four vertical cylindrical mounting standoffs rising from the bottom floor to 10 mm height, each with 5 mm outer diameter and a 2.5 mm center screw hole, positioned at a 78 mm by 42 mm rectangular pitch centered inside the cavity. On the left 55 mm side wall, cut a rectangular USB Type-C port opening 9.2 mm wide and 3.4 mm high, centered horizontally and positioned 4 mm above the bottom floor. Next to it on the same wall, cut a rectangular slide switch slot 7 mm wide and 3.5 mm high.
Parameters
| Name | Value | Range |
|---|---|---|
| Overall length, X | 91 mm | 40 – 200 |
| Overall width, Y | 55 mm | 30 – 150 |
| Overall height, Z | 18 mm | 8 – 60 |
| Outer vertical corner fillet | 2 mm | 0 – 8 |
| Wall thickness | 2 mm | 1.2 – 5 |
| Bottom floor thickness | 2 mm | 1.2 – 6 |
| Standoff outer diameter | 5 mm | 3 – 10 |
| Center screw hole diameter | 2.5 mm | 1.5 – 5 |
| Standoff height above floor | 10 mm | 3 – 16 |
| Standoff pitch in X | 78 mm | 20 – 120 |
| Standoff pitch in Y | 42 mm | 20 – 100 |
| Opening width | 9.2 mm | 5 – 20 |
| Opening height | 3.4 mm | 2 – 10 |
| Bottom of opening above floor | 4 mm | 1 – 12 |
| Opening centre offset along wall | 0 mm | -20 – 20 |
| Slot width | 7 mm | 3 – 20 |
| Slot height | 3.5 mm | 2 – 10 |
| Bottom of slot above floor | 4 mm | 1 – 12 |
| Slot centre offset along wall | 15 mm | -20 – 20 |
Every value above is a live dimension. Open a model like this in the editor and each one becomes a slider you can drag before exporting.
More models
Browse the full gallery →UAV Ogive Nose Cone
Design a watertight, 3D-printable aerodynamic nose cone module for a fixed-wing tactical UAV, optimized for printing in Carbon Fiber Filled PETG (PETG-CF). The base of the nose con
Trumpet Lyre Mount Main Body
A single 3D mechanical CAD part for a trumpet music lyre mount (Main Body with Paddle). Geometry details: 1. A 18mm-wide semi-cylindrical clamp arc for a 28mm diameter cylinder, w
Flat-Strap Reel Spool
Create a 3D model of a custom flat-strap reel spool for a home plate housing cavity. Geometry: - A reel spool consisting of two parallel circular outer flanges connected by a cent
PET Recycling Kiosk Frame
Design a production-ready welded steel frame for an outdoor PET bottle recycling and animal feeding kiosk. Create ONLY the steel frame. Do not create covers, motors, tanks, electr
JZX100 Gas Cap Holder
can you make a gas cap holder for a jzx100 chaser. i want you to refer to the image and make a cad very close to the picture
Micro RC Airplane Frame
Create a lightweight 3D-printable indoor micro RC airplane frame. The fuselage is a hollow rectangular boom 200 mm long, 3 mm wide, and 3 mm tall, with an open U-shaped electronics
