Brackets and mounts
Linear Screw Stage
- Bounding box
- 396 × 71 × 71 mm
- Engine
- 3D Printing B-rep
- Parameters
- 30
- Published
- November 19, 2026
Download
Free to download and use. See the terms.
The prompt
3D CAD model of a linear screw stage in mm. Overall rail/span length is 396 mm. Left end plate is 42 mm wide x 57 mm high x 8 mm thick with a bore at 42.5 mm height and a 25 mm long, 20 mm high clamped bearing block. Right motor mount plate is 71 mm high x 8 mm thick with a Ø22 mm center bore, 31x31 mm inner M4-4 hole pattern, and 47.14x47.14 mm outer mounting holes. Two parallel rails are spaced 30 mm apart (18.2 mm from bottom, 4.2 mm from edge) with M4 slider nuts. A lead screw with coupling runs between ends, and a sliding carriage block reaches 59.5 mm height from the bottom with two M4 holes spaced 17 mm apart (7.5 mm offset, 29.5 mm reference).
Parameters
| Name | Value | Range |
|---|---|---|
| Overall rail span | 396 mm | 200 – 700 |
| Rail centre-to-centre spacing | 30 mm | 15 – 80 |
| Rail centreline height above datum | 18.2 mm | 8 – 60 |
| Rail body width | 9 mm | 5 – 20 |
| Rail body height | 8 mm | 4 – 20 |
| Rail T-slot width | 4.6 mm | 2 – 8 |
| Left plate width | 42 mm | 20 – 120 |
| Left plate height | 57 mm | 20 – 150 |
| Plate thickness | 8 mm | 4 – 20 |
| Screw axis height | 42.5 mm | 10 – 120 |
| Bearing bore diameter | 12 mm | 8 – 25 |
| Right plate width | 71 mm | 30 – 150 |
| Right plate height | 71 mm | 30 – 150 |
| Motor shaft bore | 22 mm | 10 – 40 |
| Inner M4 hole pattern | 31 mm | 10 – 60 |
| Outer M4 hole pattern | 47.14 mm | 10 – 80 |
| M4 clearance hole diameter | 4.5 mm | 3.3 – 6 |
| Block length along axis | 25 mm | 10 – 50 |
| Block height | 20 mm | 10 – 50 |
| Block width | 30 mm | 10 – 60 |
| Block bore diameter | 12 mm | 6 – 24 |
| Screw diameter | 10 mm | 4 – 25 |
| Screw length | 380 mm | 100 – 600 |
| Coupling diameter | 22 mm | 10 – 40 |
| Coupling length | 25 mm | 10 – 50 |
| Carriage length along axis | 60 mm | 20 – 120 |
| Carriage width across rails | 44 mm | 20 – 120 |
| Carriage top height above datum | 59.5 mm | 20 – 120 |
| M4 mounting hole spacing | 17 mm | 5 – 60 |
| M4 hole offset from carriage edge | 7.5 mm | 1 – 40 |
Every value above is a live dimension. Open a model like this in the editor and each one becomes a slider you can drag before exporting.
More models
Browse the full gallery →UAV Ogive Nose Cone
Design a watertight, 3D-printable aerodynamic nose cone module for a fixed-wing tactical UAV, optimized for printing in Carbon Fiber Filled PETG (PETG-CF). The base of the nose con
Trumpet Lyre Mount Main Body
A single 3D mechanical CAD part for a trumpet music lyre mount (Main Body with Paddle). Geometry details: 1. A 18mm-wide semi-cylindrical clamp arc for a 28mm diameter cylinder, w
Flat-Strap Reel Spool
Create a 3D model of a custom flat-strap reel spool for a home plate housing cavity. Geometry: - A reel spool consisting of two parallel circular outer flanges connected by a cent
PET Recycling Kiosk Frame
Design a production-ready welded steel frame for an outdoor PET bottle recycling and animal feeding kiosk. Create ONLY the steel frame. Do not create covers, motors, tanks, electr
JZX100 Gas Cap Holder
can you make a gas cap holder for a jzx100 chaser. i want you to refer to the image and make a cad very close to the picture
Micro RC Airplane Frame
Create a lightweight 3D-printable indoor micro RC airplane frame. The fuselage is a hollow rectangular boom 200 mm long, 3 mm wide, and 3 mm tall, with an open U-shaped electronics
