167.882.824.3
Loading the interactive model…
Interactive 3D model of Leitz Phone 1 Fan-Cooled Two-Piece Case

Enclosures and housings

Leitz Phone 1 Fan-Cooled Two-Piece Case

1 views
Bounding box
82.8 × 167.8 × 24.3 mm
Engine
Precision B-rep
Parameters
45
Published
November 20, 2026

Download

Free to download and use. See the terms.

The prompt

Design a two-part 3D-printable phone case with an integrated cooling fan, fitted to the Leitz Phone 1. Output a parametric, dimensioned model (STEP and STL), millimetres, with all key values as named parameters. PHONE (official, excluding camera bump): - Width 74.0, height 162.0, thickness 9.5 (flat slab, rounded corners) - Corner radius: not published. Use 10 as a named parameter. - Camera bump on the back (top area), key positions on the side, and USB-C position: not published. Expose as parameters with these defaults: camera window 34x34 at 8 mm from the left edge and 10 mm from the top; power/volume keys on the right edge, 90 mm from the bottom, 40 mm long; USB-C centred on the bottom edge, 12x5 cutout. - Fit clearance 0.4 mm around the phone. PART 1, TRAY (holds the phone): - Phone pocket, open back, front lip 1.6 mm with a 2 mm bezel overlap and a full screen window. Side walls 4 mm (left/right), 2.5 mm (top/bottom). - Cutouts for the keys and the USB-C port, with 1 mm margin. - Four M2 self-tapping pilot holes (1.8 mm) in the side walls at y = 20 mm and y = height - 20 mm. PART 2, COOLING COVER (mates to the tray back): - Same outer footprint as the tray, total depth about 12.8 mm. - Open cavity facing the phone's back, 1.6 mm floor. - Fan pocket at the top: 4010 blower, 40 x 40 x 10 mm, intake facing OUTWARD through a 28 mm round grill with cross ribs in the floor, outlet facing down toward the phone's lower back. Retaining walls around three sides of the fan. - Exhaust slots through both long side walls, 4 slots each, 5 mm wide, 9 mm pitch, starting 42 mm from the bottom. - Electronics bay at the bottom: 33 mm long, separated by a 2 mm partition, sized for a LiPo 603040 (6x30x40 mm) plus a TP4056 USB-C module (about 26x17x4 mm) and a small controller board stacked above the battery. - Cutouts in the bottom wall: USB-C charging port (12x5) and a slide switch (6x4). - Four M2 counterbored screw holes (2.4 mm through, 3.6 mm head) that line up with the tray pilots. - Optional camera window in the floor (parameter, off by default). PRINT RULES: - FDM, PETG or ABS, 0.2 mm layers, minimum wall 1.6 mm, no overhangs steeper than 45 degrees without support. - Tray prints front face down; cover prints outer face down. - Round all exterior edges 1 mm where possible. Before exporting, list any dimension you assumed

Parameters

NameValueRange
Phone Width74 mm60 – 90
Phone Height162 mm130 – 190
Phone Corner Radius10 mm2 – 20
Fit Clearance (per side)0.4 mm0.1 – 1
Front Lip Thickness1.6 mm1 – 3
Screen Bezel Overlap2 mm1 – 6
Side Wall Thickness4 mm2 – 8
Top/Bottom Wall Thickness2.5 mm1.6 – 6
Tray Depth11.5 mm8 – 16
Outer Corner Radius10.5 mm2 – 20
Key Cutout Length42 mm20 – 60
Key Cutout Height8 mm4 – 14
Key Cutout Centre from Bottom90 mm20 – 140
Tray USB-C Cutout Width14 mm8 – 22
Tray USB-C Cutout Height7 mm4 – 12
M2 Pilot Hole Diameter1.8 mm1.2 – 3
M2 Pilot Depth6 mm3 – 10
Screw Row Offset from Bottom20 mm6 – 40
M2 Through Hole Diameter2.4 mm2 – 4
Counterbore Diameter3.6 mm3 – 6
Counterbore Depth1.2 mm0.5 – 3
Cover Depth12.8 mm8 – 20
Cover Side Wall1.6 mm1.2 – 3
Cover Floor Thickness1.6 mm1.2 – 3
Fan Pocket Size40 mm30 – 50
Fan Retaining Wall Height10 mm6 – 14
Intake Grill Diameter28 mm15 – 36
Grill Cross Rib Width3 mm1 – 6
Exhaust Slot Width5 mm2 – 10
Exhaust Slot Pitch9 mm6 – 20
Exhaust Slots per Side4 pcs1 – 8
First Slot from Bottom42 mm20 – 80
Electronics Bay Width33 mm20 – 60
Electronics Bay Height42 mm30 – 70
Partition Wall Thickness2 mm1 – 4
Charge Port Cutout Width12 mm8 – 18
Charge Port Cutout Height5 mm3 – 10
Slide Switch Cutout Width6 mm3 – 12
Slide Switch Cutout Height4 mm2 – 8
Switch Centre from Right Edge12 mm4 – 30
Camera Window Size34 mm20 – 45
Camera Window from Left8 mm2 – 30
Camera Window from Top10 mm2 – 30
Enable Camera Window (0/1)0 -0 – 1
Exterior Edge Round0.6 mm0 – 1.5

Every value above is a live dimension. Open a model like this in the editor and each one becomes a slider you can drag before exporting.

3D preview of Cylindrical Stainless Steel Basket with Folding Handles368.0 × 250.0 × 252.1 mmPrecision

Cylindrical Stainless Steel Basket with Folding Handles

Design a cylindrical 304 stainless steel basket with an outer diameter of 200 mm and height of 250 mm. The basket has solid side walls with no perforations. The bottom plate contai

STEPSTLGLB15 PARAMS
3D preview of Lego 1x4 Technic Brick31.8 × 7.8 × 11.3 mmPrecision

Lego 1x4 Technic Brick

Create a precise 3D CAD model of a single 1x4 Lego Technic-compatible brick designed for STEM robotics. The main rectangular body must have exact dimensions: 31.8 mm in length, 7.8

STEPSTLGLB15 PARAMS
3D preview of Immersion Cooling Enclosure592.0 × 402.0 × 166.0 mmPrecision

Immersion Cooling Enclosure

Design a sealed high-pressure dielectric immersion cooling enclosure for cylindrical battery cells. Internal cavity dimensions: 540mm length, 360mm width, 160mm height with 6mm wal

STEPSTLGLB15 PARAMS
3D preview of Oval Safety Snap Carabiner46.5 × 12.0 × 80.0 mmPrecision

Oval Safety Snap Carabiner

Create a simple alloy steel safety snap carabiner for me to download to solidworks. I should be able to link it to a ring of another part in solidworks.

STEPSTLGLB7 PARAMS
3D preview of Simple BWB with Propulsion Tube2130.0 × 6500.0 × 350.0 mmPrecision

Simple BWB with Propulsion Tube

Prompt: "A simple, solid Blended Wing Body (BWB) flying wing. Dimensions: wingspan 6.5 meters, center chord 1.53 meters, root thickness 35 centimeters, tapering to 15 centimeters a

STEPSTLGLB8 PARAMS
3D preview of Engranaje recto 50 dientes, módulo 2104.0 × 103.9 × 10.0 mmPrecision

Engranaje recto 50 dientes, módulo 2

Engranaje recto de 50 dientes, diámetro exterior 104 mm, diámetro de raíz 95 mm, espesor 10 mm y ángulo de presión 20°. Crear como sólido 3D con un agujero central de 8.2 mm de diá

STEPSTLGLB5 PARAMS
Leitz Phone 1 Fan-Cooled Two-Piece Case - Free CAD Model (STEP, STL) | TextoCAD