Enclosures and housings
Industrial Electronics Enclosure with Terminal Access
- Bounding box
- 360.0 × 137.2 × 40.6 mm
- Engine
- Precision B-rep
- Parameters
- 54
- Published
- September 17, 2026
Download
Free to download and use. See the terms.
The prompt
Modify the existing enclosure. Keep the external dimensions 170 x 110 x 100 mm, the removable lid, M3 screw bosses, PCB standoffs, and rear 50 x 50 x 10 mm fan opening. Add real connection access features: 1. On the left long wall, add one recessed rectangular terminal access opening for 15 sensor/feedback terminals. Use 5.08 mm terminal pitch. Opening size approximately 82 mm wide x 16 mm high. Add 15 small visible terminal divisions and label the group: SENSOR / FEEDBACK 1–15. 2. On the right long wall, add an identical recessed rectangular terminal access opening for 15 sensor/feedback terminals. Use 5.08 mm pitch. Add 15 small terminal divisions and label the group: SENSOR / FEEDBACK 16–30. 3. On the front short wall, add a separate small 2-position power terminal access opening for POWER + and GND. Use 5.08 mm pitch, approximately 14 mm wide x 16 mm high. Clearly label the two positions: POWER + and GND. 4. Inside the enclosure, add clear wire-routing space from all 32 terminals to the 150 x 90 mm PCB. Add cable tie slots and routing channels. Keep at least 20 mm vertical free space above the PCB for wiring, soldering, and maintenance. Use recessed industrial terminal windows, not loose round holes. Keep the design printable, robust, clean, and suitable for a factory control panel.
Parameters
| Name | Value | Range |
|---|---|---|
| Base Length | 170 mm | 120 – 250 |
| Base Width | 110 mm | 80 – 160 |
| Base Height | 100 mm | 60 – 150 |
| Wall Thickness | 3 mm | 2 – 6 |
| Floor Thickness | 3 mm | 2 – 6 |
| Corner Radius | 5 mm | 1 – 15 |
| Exploded Layout Gap | 20 mm | 5 – 60 |
| PCB Length | 150 mm | 100 – 200 |
| PCB Width | 90 mm | 60 – 140 |
| Standoff Inset | 5 mm | 2 – 10 |
| Standoff Boss Diameter | 8 mm | 5 – 12 |
| Standoff Hole Diameter | 3.2 mm | 2.2 – 4 |
| Standoff Hole Depth | 6 mm | 3 – 12 |
| Standoff Height | 15 mm | 8 – 25 |
| Insert Boss Diameter | 8 mm | 6 – 12 |
| Insert Hole Diameter | 3.2 mm | 2.2 – 4 |
| Insert Depth | 6 mm | 3 – 10 |
| Opto Pattern X | 50 mm | 30 – 70 |
| Opto Pattern Y | 30 mm | 20 – 50 |
| Opto Pad Height | 4 mm | 2 – 8 |
| Opto Pad Size | 12 mm | 8 – 20 |
| Opto Hole Spacing | 8 mm | 5 – 12 |
| Opto Hole Diameter | 2.5 mm | 1.5 – 3.5 |
| Fan Center Z | 50 mm | 30 – 80 |
| Fan Cutout Diameter | 50 mm | 40 – 60 |
| Fan Hole Spacing | 40 mm | 30 – 50 |
| Fan Hole Diameter | 3.2 mm | 2.2 – 4 |
| Vent Slot Count | 4 | 1 – 8 |
| Vent Slot Offset | 10 mm | 4 – 20 |
| Vent Slot Pitch | 8 mm | 4 – 16 |
| Vent Slot Width | 20 mm | 10 – 30 |
| Vent Slot Height | 8 mm | 4 – 14 |
| Lid Height | 6 mm | 3 – 12 |
| Lid Top Thickness | 3 mm | 1.5 – 6 |
| Lid Lip Clearance | 0.4 mm | 0.1 – 1 |
| Lid Hole Diameter | 3.4 mm | 2.4 – 4.5 |
| Lid Edge Fillet | 1 mm | 0.2 – 3 |
| Terminal Count Left/Right | 15 | 10 – 24 |
| Terminal Pitch | 5.08 mm | 3.5 – 7.5 |
| Terminal Opening Width | 82 mm | 60 – 120 |
| Terminal Opening Height | 16 mm | 10 – 25 |
| Terminal Center Z | 30 mm | 15 – 70 |
| Front Terminal Width | 14 mm | 10 – 20 |
| Front Terminal Height | 16 mm | 10 – 25 |
| Front Terminal Center Z | 30 mm | 15 – 70 |
| Power Terminal Pitch | 5.08 mm | 3.5 – 7.5 |
| Terminal Division Width | 0.6 mm | 0.3 – 1.2 |
| Terminal Division Depth | 0.6 mm | 0.3 – 1.2 |
| Terminal Division Length | 2 mm | 1 – 4 |
| Routing Channel Width | 8 mm | 5 – 15 |
| Routing Channel Depth | 1.5 mm | 0.5 – 3 |
| Cable Tie Slot Length | 8 mm | 4 – 14 |
| Cable Tie Slot Width | 2 mm | 1 – 4 |
| Cable Tie Slots Per Side | 2 | 1 – 4 |
Every value above is a live dimension. Open a model like this in the editor and each one becomes a slider you can drag before exporting.
More models
Browse the full gallery →Cylindrical Stainless Steel Basket with Folding Handles
Design a cylindrical 304 stainless steel basket with an outer diameter of 200 mm and height of 250 mm. The basket has solid side walls with no perforations. The bottom plate contai
Immersion Cooling Enclosure
Design a sealed high-pressure dielectric immersion cooling enclosure for cylindrical battery cells. Internal cavity dimensions: 540mm length, 360mm width, 160mm height with 6mm wal
Simple BWB with Propulsion Tube
Prompt: "A simple, solid Blended Wing Body (BWB) flying wing. Dimensions: wingspan 6.5 meters, center chord 1.53 meters, root thickness 35 centimeters, tapering to 15 centimeters a
Engranaje recto 50 dientes, módulo 2
Engranaje recto de 50 dientes, diámetro exterior 104 mm, diámetro de raíz 95 mm, espesor 10 mm y ángulo de presión 20°. Crear como sólido 3D con un agujero central de 8.2 mm de diá
G+1 Party Hall Structural Shell
G+1 Party Hall – AutoCAD Design Prompt Design a G+1 RCC-framed Party Hall in AutoCAD with detailed Ground Floor Plan, First Floor Plan, and all-side elevations (front, rear, left
Rope Winch Drum
Create a fully parametric CAD model of a rope winch drum for a construction hoist. Requirements: - Output format: STEP (.step or .stp) - Units: millimeters - Solid body only (no