3D preview of Indexing Support Bracket
Loading the interactive model…
Interactive 3D model of Indexing Support Bracket

Brackets and mounts

Indexing Support Bracket

1 views
Bounding box
125.4 × 105.4 × 114.0 mm
Engine
Precision B-rep
Parameters
17
Published
November 17, 2026

Download

Free to download and use. See the terms.

The prompt

Built Indexing Support Bracket (Precision). You asked for a CAD file (STEP), so this was built with Precision. REJECT — 7 hard failure(s); built to: 'Pieza mecánica paramétrica — matriz circular superior con soportes inferiores (Fila 29)', x∈[-62.7,62.7]mm, y∈[-52.69,52.69]mm, z∈[0.0,114.0]mm, D1 diámetro círculos inferiores base=20.0±0.05mm, D2 diámetro exterior soportes inferiores=38.0±0.05mm, D3 diámetro círculo de distribución de centros (matriz superior)=59.66±0.05mm, D4 diámetro agujeros matriz superior=7.21±0.05mm, D5 diámetro agujero central superior=33.0±0.05mm, D6 altura de referencia vertical general=114.0±0.5mm, R1 radio de acuerdo / empalme inferior=36.36±0.05mm, R2 radio de curvatura interior=18.18±0.05mm, R3 radio del arco inferior central=15.0±0.05mm, R4 radio del contorno exterior principal=52.69±0.05mm, L1 longitud de referencia para nervios/costillas=125.4±0.5mm, E1 espesor/altura extrusión central=24.0±0.05mm, E2 espesor superior sección soportes=21.0±0.05mm, E3 espesor inferior sección soportes=18.0±0.05mm, E4 profundidad/espesor costilla superior=7.0±0.05mm, E5 espesor de referencia simétrico=7.0±0.05mm, E6 desplazamiento de corte interno=6.0±0.05mm, E7 medida complementaria de espesor en sección=8.0±0.05mm, 23 holes, 1 holes, 2 holes, fillet r=36.36mm on acuerdo_inferior, fillet r=18.18mm on curvatura_interior, watertight • [bbox] x-extent 105.38mm is outside allowed [-62.7,62.7]mm (expected=[-62.7, 62.7], got=105.38) • [bbox] y-extent 195.35mm is outside allowed [-52.69,52.69]mm (expected=[-52.69, 52.69], got=195.352) • [bbox] L1 longitud de referencia para nervios/costillas (x) is 105.38mm, expected 125.4±0.5mm (expected=125.4, got=105.38) • [hole_count] measured 26 holes from geometry, but spec requires 23 (expected=23, got=26) • [hole_count] measured 26 holes from geometry, but spec requires 1 (expected=1, got=26) • [hole_count] measured 26 holes from geometry, but spec requires 2 (expected=2, got=26) • [fillet] fillet present but no rounded face matches r=18.18mm (found radii [52.69, 34.68, 3.6, 3.6, 3.6, 3.6, 3.6, 3.6, 3.6, 3.6, 3.6, 3.6, 3.6, 3.6, 3.6, 22.5, 3.6, 3.6, 3.6, 3.6, 3.6, 3.6, 3.6, 3.6, 3.6, 3.6, 36.36, 16.5, 31.5, 19.0, 10.0, 19.0, 10.0]mm) (expected='r=18.18', got=[52.69, 34.68, 3.605, 3.605, 3.605, 3.605, 3.605, 3.605, 3.605, 3.605, 3.605, 3.605, 3.605, 3.605, 3.605, 22.5, 3.605, 3.605, 3.605, 3.605, 3.605, 3.605, 3.605, 3.605, 3.605, 3.605, 36.36, 16.5, 31.5, 19.0, 10.0, 19.0, 10.0])

Parameters

NameValueRange
Overall Height (D6)114 mm60 – 250
Base Length (L1)125.4 mm60 – 250
Base Depth60 mm20 – 110
Base Thickness (E3)18 mm4 – 50
Base Corner Radius6 mm0.5 – 12
Support Boss Diameter (D2)38 mm8 – 70
Support Bore Diameter (D1)20 mm2 – 50
Support Boss Height34 mm8 – 80
Support Centre Offset43.7 mm10 – 110
Column Width52 mm15 – 100
Column Depth40 mm15 – 100
Top Plate Diameter (2xR4)105.38 mm40 – 180
Top Plate Thickness (E1)24 mm4 – 60
Central Bore Diameter (D5)33 mm3 – 90
Bolt Circle Diameter (D3)59.66 mm15 – 160
Bolt Hole Diameter (D4)7.21 mm1.5 – 20
Bolt Hole Count8 holes3 – 12

Every value above is a live dimension. Open a model like this in the editor and each one becomes a slider you can drag before exporting.