Enclosures and housings
Hinged Checker Tray Case with UV Lid and Left Wire Notch
- Bounding box
- 377.0 × 343.2 × 244.9 mm
- Engine
- Precision B-rep
- Parameters
- 30
- Published
- September 27, 2026
Download
Free to download and use. See the terms.
The prompt
Add a small wire exit notch on the left end of the case, aligned with the UV light strip channel in the lid, so the cord can pass out of the enclosure while the lid is closed. Make the notch approximately 6 mm x 4 mm with rounded edges, and keep it parametric.
Parameters
| Name | Value | Range |
|---|---|---|
| Wall Thickness | 2.5 mm | 1.2 – 5 |
| Bottom Thickness | 3 mm | 1.5 – 8 |
| Tray Height | 45 mm | 20 – 90 |
| Corner Fillet Radius | 5 mm | 0 – 12 |
| Checker Slots Per Side | 15 count | 1 – 30 |
| Checker Slot Width | 10 mm | 5 – 25 |
| Checker Channel Depth | 40 mm | 20 – 70 |
| Separator Thickness | 1.5 mm | 0.8 – 4 |
| Tab Height | 12 mm | 3 – 40 |
| Edge Tab Length | 6 mm | 1 – 20 |
| Checker Diameter | 38 mm | 10 – 60 |
| Checker Thickness | 8.5 mm | 2 – 30 |
| Dice Compartment Length | 25 mm | 10 – 60 |
| Dice Compartment Width | 30 mm | 10 – 60 |
| Hinge Pin Diameter | 4 mm | 1.5 – 10 |
| Knuckle Outer Diameter | 12 mm | 5 – 25 |
| Knuckle Gap | 0.8 mm | 0.2 – 3 |
| Knuckle Pitch | 25 mm | 10 – 60 |
| Hinge End Margin | 10 mm | 0 – 40 |
| Hinge Pin Overhang | 4 mm | 0 – 20 |
| Lid Open Angle | 75 deg | 0 – 150 |
| Lid Skirt Height | 50 mm | 15 – 120 |
| Lid Top Thickness | 8 mm | 2 – 20 |
| Lid Wall Thickness | 4 mm | 1.5 – 10 |
| UV Strip Channel Width | 20 mm | 5 – 60 |
| UV Strip Channel Depth | 5 mm | 1 – 12 |
| Wire Hole Diameter (right end) | 6 mm | 2 – 15 |
| Wire Notch Width | 6 mm | 2 – 20 |
| Wire Notch Height | 4 mm | 1 – 15 |
| Wire Notch Corner Radius | 1.5 mm | 0.5 – 3 |
Every value above is a live dimension. Open a model like this in the editor and each one becomes a slider you can drag before exporting.
More models
Browse the full gallery →Cylindrical Stainless Steel Basket with Folding Handles
Design a cylindrical 304 stainless steel basket with an outer diameter of 200 mm and height of 250 mm. The basket has solid side walls with no perforations. The bottom plate contai
Immersion Cooling Enclosure
Design a sealed high-pressure dielectric immersion cooling enclosure for cylindrical battery cells. Internal cavity dimensions: 540mm length, 360mm width, 160mm height with 6mm wal
Simple BWB with Propulsion Tube
Prompt: "A simple, solid Blended Wing Body (BWB) flying wing. Dimensions: wingspan 6.5 meters, center chord 1.53 meters, root thickness 35 centimeters, tapering to 15 centimeters a
Engranaje recto 50 dientes, módulo 2
Engranaje recto de 50 dientes, diámetro exterior 104 mm, diámetro de raíz 95 mm, espesor 10 mm y ángulo de presión 20°. Crear como sólido 3D con un agujero central de 8.2 mm de diá
G+1 Party Hall Structural Shell
G+1 Party Hall – AutoCAD Design Prompt Design a G+1 RCC-framed Party Hall in AutoCAD with detailed Ground Floor Plan, First Floor Plan, and all-side elevations (front, rear, left
Rope Winch Drum
Create a fully parametric CAD model of a rope winch drum for a construction hoist. Requirements: - Output format: STEP (.step or .stp) - Units: millimeters - Solid body only (no