Enclosures and housings
Hinged Checker Case with UV Lid and Cable Notch
- Bounding box
- 95.7 × 81.9 × 76.0 mm
- Engine
- Precision B-rep
- Parameters
- 30
- Published
- September 27, 2026
Download
Free to download and use. See the terms.
The prompt
Do not change the existing tray, lid, hinge geometry, hinge axis, lid orientation, or dimensions. Keep the current hinged case exactly as it was before this modification. Make only one change: Add a small cable pass-through notch at the left end of the case, close to the UV light strip channel, so the UV power cable can exit while the lid is closed. The notch should be approximately 6 mm wide × 4 mm high, with slightly rounded edges. The notch should be cut into the edge of the enclosure only. Do not move, rotate, resize, rebuild, or add any hinges. Do not rotate or reposition the lid. Do not change the checker tray or dice compartment. Preserve the exact existing relationship between the lid and bottom tray.
Parameters
| Name | Value | Range |
|---|---|---|
| Side Wall Thickness | 3 mm | 1.5 – 6 |
| Bottom Thickness | 3 mm | 1.5 – 6 |
| Tray Height | 30 mm | 15 – 60 |
| Corner Fillet Radius | 4 mm | 0.5 – 6 |
| Checker Slots Per Side | 4 ea | 2 – 8 |
| Checker Slot Width | 4 mm | 3 – 12 |
| Checker Channel Depth | 28 mm | 10 – 60 |
| Separator Rib Thickness | 2 mm | 1 – 4 |
| Separator Height | 12 mm | 5 – 40 |
| Separator Tab Length | 8 mm | 2 – 30 |
| Checker Diameter | 25 mm | 10 – 40 |
| Checker Thickness | 3 mm | 1 – 8 |
| Dice Bay Length | 30 mm | 15 – 60 |
| Dice Bay Width | 30 mm | 10 – 60 |
| Hinge Pin Diameter | 3 mm | 1.5 – 6 |
| Knuckle Outer Diameter | 8 mm | 4 – 16 |
| Knuckle Gap | 0.6 mm | 0.3 – 3 |
| Knuckle Pitch | 20 mm | 8 – 50 |
| Hinge End Margin | 6 mm | 2 – 20 |
| Hinge Pin Overhang | 4 mm | 0.5 – 20 |
| Lid Open Angle | 110 deg | 0 – 180 |
| Lid Height | 20 mm | 8 – 50 |
| Lid Top Thickness | 3 mm | 2 – 8 |
| Lid Wall Thickness | 3 mm | 1.5 – 6 |
| UV Strip Channel Width | 20 mm | 5 – 60 |
| UV Strip Channel Depth | 4 mm | 1 – 12 |
| Wire Hole Diameter | 4 mm | 1.5 – 10 |
| Cable Notch Width | 6 mm | 2 – 20 |
| Cable Notch Height | 4 mm | 1 – 15 |
| Cable Notch Corner Radius | 1 mm | 0 – 3 |
Every value above is a live dimension. Open a model like this in the editor and each one becomes a slider you can drag before exporting.
More models
Browse the full gallery →Cylindrical Stainless Steel Basket with Folding Handles
Design a cylindrical 304 stainless steel basket with an outer diameter of 200 mm and height of 250 mm. The basket has solid side walls with no perforations. The bottom plate contai
Immersion Cooling Enclosure
Design a sealed high-pressure dielectric immersion cooling enclosure for cylindrical battery cells. Internal cavity dimensions: 540mm length, 360mm width, 160mm height with 6mm wal
Simple BWB with Propulsion Tube
Prompt: "A simple, solid Blended Wing Body (BWB) flying wing. Dimensions: wingspan 6.5 meters, center chord 1.53 meters, root thickness 35 centimeters, tapering to 15 centimeters a
Engranaje recto 50 dientes, módulo 2
Engranaje recto de 50 dientes, diámetro exterior 104 mm, diámetro de raíz 95 mm, espesor 10 mm y ángulo de presión 20°. Crear como sólido 3D con un agujero central de 8.2 mm de diá
G+1 Party Hall Structural Shell
G+1 Party Hall – AutoCAD Design Prompt Design a G+1 RCC-framed Party Hall in AutoCAD with detailed Ground Floor Plan, First Floor Plan, and all-side elevations (front, rear, left
Rope Winch Drum
Create a fully parametric CAD model of a rope winch drum for a construction hoist. Requirements: - Output format: STEP (.step or .stp) - Units: millimeters - Solid body only (no