Brackets and mounts
Flight Stick Handheld Controller - Exploded Assembly
- Bounding box
- 455.9 × 90.0 × 125.0 mm
- Engine
- Precision B-rep
- Parameters
- 45
- Published
- November 19, 2026
Download
Free to download and use. See the terms.
The prompt
lets do it again this time give me simple sketches first and if approved we proceed design me a handheld stick, like a fighter jet stick like what i provided in the image keep its ergonomic form but its ok if you change it a bit making it look more badass as long as you dont ruin the ergonomics, and with a place for ESP32 and gyro on top. And some buttons, so I can place some micro switches underneath them and use them as extra controlling channels. And a place on top of it so I can use my thumb to move a potentiometer, more like a volume slider, fader slider, something like that. The size of the volume slider is 5.5 millimeters thick. It is 18.2 millimeters long and 5 millimeters height. The moving part is 3 millimeters by 1.4 millimeters, and its height is 2.5 millimeters. Also, it has four pins at bottom on each corner. The pins are 1.2 millimeters by 0.5 millimeters, and their height is 2.5 millimeters. They will be used to fixate the volume. Also, there are 3 pins underneath, so I can use them and connect wires to them same size is fixture pins. also I need clear covers so I can see my ESP32 LEDs they should be separate parts so i can print them using clear PETG. We need a USB-C port for charging, and I have this lithium charging module, which is about 17 millimeters wide. The length is 28 millimeters and the height is 4.2 millimeters. But of course we need to add some value for margin, tolerance margin. It also have two LEDs attached to it. the USB port itself is about 1.2 millimeters out of the board, so we can count on that. And the LEDs are 8.5 millimeters away from the USB port for the first one, and 12.5 millimeters from the board The second one, they're at the right side of the board and they're almost stuck to the edge of the board with like 1.5 millimeters away. The 28 millimeters length I described is plus the USB-C port. We also need a power button on the body of our joystick, and we need it to be ergonomic, and it's okay, we will use the 18650 battery. I should also mention that I have these power buttons. It's 8.63 millimeters by 3.8 millimeters, and the height of 3.9 millimeters. It also has a stick for turning it on and off with 1.5 by 1.5 millimeters, and the height of the stick is 5.5 millimeters. and finally my micro switches 6 by 6 and 4 mm tall and the button is a cylinder 3.5mm diameter and 6.5 mm tall. ive stuck the imu module under the esp board making it 3.5mm longer and and make it 9mm thick and also the esp needs ventilation. keep in mind that it should be 3d printable and the esp32 light should be visible from top and slider should be almost collinear with the handle also put the second switch bottom of the slider then make 3d model, its better if it is assembled step file so i can see how i should be assembled, we also need some channels for wiring the stuff together and both ends of the battery holder should be a little flexible with a part i can tie some wire around it
Parameters
| Name | Value | Range |
|---|---|---|
| Grip Width (X) | 48 mm | 30 – 80 |
| Grip Depth (Y) | 60 mm | 30 – 100 |
| Grip Height (Z) | 125 mm | 80 – 200 |
| Wall Thickness | 2.5 mm | 1.2 – 5 |
| Floor Thickness | 4 mm | 2 – 10 |
| Battery Bay Diameter | 19.4 mm | 18 – 24 |
| Battery Bay Depth | 68 mm | 50 – 90 |
| Deck Length (Y) | 60 mm | 40 – 90 |
| Deck Width (X) | 48 mm | 30 – 80 |
| Deck Height (Z) | 20 mm | 12 – 35 |
| Fader Thickness | 5.5 mm | 3 – 12 |
| Fader Length | 18.2 mm | 10 – 40 |
| Fader Height | 5 mm | 2 – 12 |
| Moving Part Width | 1.4 mm | 0.6 – 5 |
| Moving Part Length | 3 mm | 1.5 – 8 |
| Moving Part Height | 2.5 mm | 1 – 6 |
| Pin Width | 1.2 mm | 0.4 – 3 |
| Pin Thickness | 0.5 mm | 0.3 – 2 |
| Pin Height | 2.5 mm | 1 – 6 |
| ESP32 Board Length | 25.4 mm | 15 – 45 |
| ESP32 Board Width | 18 mm | 12 – 30 |
| ESP32 + IMU Stack Height | 9 mm | 4 – 20 |
| IMU Board Overhang | 3.5 mm | 0 – 12 |
| TP4056 Width | 17 mm | 10 – 30 |
| TP4056 Length (incl. USB-C) | 28 mm | 15 – 45 |
| TP4056 Height | 4.2 mm | 2 – 10 |
| USB-C Protrusion | 1.2 mm | 0.5 – 4 |
| 18650 Cell Diameter | 18.5 mm | 16 – 22 |
| 18650 Cell Length | 65 mm | 50 – 75 |
| Holder Wall | 1.2 mm | 0.8 – 4 |
| Power Button Width | 8.63 mm | 4 – 16 |
| Power Button Depth | 3.8 mm | 2 – 10 |
| Power Button Height | 3.9 mm | 2 – 10 |
| Lever Cross Section | 1.5 mm | 0.8 – 4 |
| Lever Height | 5.5 mm | 2 – 12 |
| Microswitch Size | 6 mm | 4 – 12 |
| Microswitch Height | 4 mm | 2 – 10 |
| Button Cap Diameter | 3.5 mm | 1.5 – 8 |
| Button Cap Height | 6.5 mm | 1 – 12 |
| ESP32 Cover Width | 12 mm | 6 – 30 |
| ESP32 Cover Length | 20 mm | 8 – 40 |
| Charger Cover Width | 7 mm | 4 – 20 |
| Charger Cover Length | 14 mm | 6 – 30 |
| Cover Thickness | 2 mm | 1 – 4 |
| Exploded Layout Gap | 25 mm | 5 – 80 |
Every value above is a live dimension. Open a model like this in the editor and each one becomes a slider you can drag before exporting.
More models
Browse the full gallery →UAV Ogive Nose Cone
Design a watertight, 3D-printable aerodynamic nose cone module for a fixed-wing tactical UAV, optimized for printing in Carbon Fiber Filled PETG (PETG-CF). The base of the nose con
Trumpet Lyre Mount Main Body
A single 3D mechanical CAD part for a trumpet music lyre mount (Main Body with Paddle). Geometry details: 1. A 18mm-wide semi-cylindrical clamp arc for a 28mm diameter cylinder, w
Flat-Strap Reel Spool
Create a 3D model of a custom flat-strap reel spool for a home plate housing cavity. Geometry: - A reel spool consisting of two parallel circular outer flanges connected by a cent
PET Recycling Kiosk Frame
Design a production-ready welded steel frame for an outdoor PET bottle recycling and animal feeding kiosk. Create ONLY the steel frame. Do not create covers, motors, tanks, electr
JZX100 Gas Cap Holder
can you make a gas cap holder for a jzx100 chaser. i want you to refer to the image and make a cad very close to the picture
Micro RC Airplane Frame
Create a lightweight 3D-printable indoor micro RC airplane frame. The fuselage is a hollow rectangular boom 200 mm long, 3 mm wide, and 3 mm tall, with an open U-shaped electronics
