3D preview of ESP32 Super Mini Enclosure - Right Half
Loading the interactive model…
Interactive 3D model of ESP32 Super Mini Enclosure - Right Half

Enclosures and housings

ESP32 Super Mini Enclosure - Right Half

1 views
Bounding box
19.5 × 45.0 × 55.0 mm
Engine
3D Printing B-rep
Parameters
16
Published
November 19, 2026

Download

Free to download and use. See the terms.

The prompt

Model a single solid, 3D-printable part in millimeters. It is "Part 2" (right half, X >= 0) of a two-piece snap-fit enclosure for an ESP32 Super Mini board. Part 1 is modeled separately, so keep every coordinate and dimension exactly as written. Do not rotate or re-center the part. Use named parameters for the main dimensions. COORDINATES X = width, Y = depth, Z = height. The closed enclosure is a rounded box: X from -12.5 to 12.5 (25 mm), Y from -22.5 to 22.5 (45 mm), Z from 0 to 55 mm. The halves split on the plane X = 0. Z = 0 is the bottom face (USB-C side). 1. HALF SHELL - Hollow half box: X from 0 to 12.5, Y from -22.5 to 22.5, Z from 0 to 55. Wall thickness 1.6 mm on all walls. Open face at X = 0 (the joint face). - Interior cavity: X from 0 to 10.9, Y from -20.9 to 20.9, Z from 1.6 to 53.4. - Fillet R2 on all outer edges except the edges lying on the open face X = 0. - The outer face at X = 12.5 is flat and plain. 2. TONGUE (half-lap joint) - Around the whole perimeter, extend the INNER 0.7 mm of the wall thickness (measured from the inside surface of the wall) past the joint plane, from X = 0 to X = -7.0. It is a thin ring 0.7 mm thick that follows the cavity outline. The outer 0.9 mm of the wall does NOT continue past X = 0. The part's bounding box therefore reaches X = -7.0 on purpose. This tongue slides into Part 1, leaving 0.2 mm clearance. 3. SNAP ARMS (4) - On the front wall (Y = -22.5) and the rear wall (Y = +22.5), at Z = 17 and Z = 38, turn the tongue into a flexible cantilever arm: 8 mm wide in Z (Z from 13 to 21 and from 34 to 42) and 7 mm long (X from 0 to -7). Cut 1 mm wide slits on both sides of each arm, through the tongue only, from X = 0 to X = -7. The arm stays attached only at X = 0. 4. HOOKS (4) - At the free end of each arm, add a hook on the OUTER face of the arm (facing away from the cavity), 8 mm wide in Z and 0.6 mm tall. Profile along X: height 0 at X = -7.0, rising linearly to 0.6 at X = -5.8 (lead-in ramp), flat crest from X = -5.8 to X = -5.4, then a vertical retention face at X = -5.4. 5. USB-C OPENING - Cut a stadium-shaped slot through the bottom wall (Z from 0 to 1.6), centered at X = 0, Y = 0. Full slot: 9.5 mm long in Y by 3.8 mm wide in X, fully rounded ends (end radius 1.9). Part 2 contains only the half with X from 0 to 1.9 and the corresponding notch in the tongue (X from -1.9 to 0) over the bottom wall. Cut the slot through the tongue too, so it stays open. Result: one single solid, no text, no extra features.

Parameters

NameValueRange
Overall X width25 mm10 – 60
Overall Y depth45 mm20 – 100
Overall Z height55 mm20 – 120
Wall thickness1.6 mm0.8 – 4
Outer edge fillet radius2 mm0.5 – 5
Tongue projection past joint7 mm3 – 12
Tongue thickness0.7 mm0.4 – 1.2
Snap arm width in Z8 mm4 – 16
Lower snap arm centre Z17 mm8 – 50
Upper snap arm centre Z38 mm8 – 50
Slit width beside arms1 mm0.4 – 3
Hook protrusion height0.6 mm0.3 – 2
Hook overall length in X1.6 mm0.6 – 4
Hook crest length in X0.4 mm0.2 – 1.5
Slot length in Y9.5 mm5 – 20
Slot width in X3.8 mm2 – 10

Every value above is a live dimension. Open a model like this in the editor and each one becomes a slider you can drag before exporting.

3D preview of Cylindrical Stainless Steel Basket with Folding Handles368.0 × 250.0 × 252.1 mmPrecision

Cylindrical Stainless Steel Basket with Folding Handles

Design a cylindrical 304 stainless steel basket with an outer diameter of 200 mm and height of 250 mm. The basket has solid side walls with no perforations. The bottom plate contai

STEPSTLGLB15 PARAMS
3D preview of Lego 1x4 Technic Brick31.8 × 7.8 × 11.3 mmPrecision

Lego 1x4 Technic Brick

Create a precise 3D CAD model of a single 1x4 Lego Technic-compatible brick designed for STEM robotics. The main rectangular body must have exact dimensions: 31.8 mm in length, 7.8

STEPSTLGLB15 PARAMS
3D preview of Immersion Cooling Enclosure592.0 × 402.0 × 166.0 mmPrecision

Immersion Cooling Enclosure

Design a sealed high-pressure dielectric immersion cooling enclosure for cylindrical battery cells. Internal cavity dimensions: 540mm length, 360mm width, 160mm height with 6mm wal

STEPSTLGLB15 PARAMS
3D preview of Oval Safety Snap Carabiner46.5 × 12.0 × 80.0 mmPrecision

Oval Safety Snap Carabiner

Create a simple alloy steel safety snap carabiner for me to download to solidworks. I should be able to link it to a ring of another part in solidworks.

STEPSTLGLB7 PARAMS
3D preview of Simple BWB with Propulsion Tube2130.0 × 6500.0 × 350.0 mmPrecision

Simple BWB with Propulsion Tube

Prompt: "A simple, solid Blended Wing Body (BWB) flying wing. Dimensions: wingspan 6.5 meters, center chord 1.53 meters, root thickness 35 centimeters, tapering to 15 centimeters a

STEPSTLGLB8 PARAMS
3D preview of Engranaje recto 50 dientes, módulo 2104.0 × 103.9 × 10.0 mmPrecision

Engranaje recto 50 dientes, módulo 2

Engranaje recto de 50 dientes, diámetro exterior 104 mm, diámetro de raíz 95 mm, espesor 10 mm y ángulo de presión 20°. Crear como sólido 3D con un agujero central de 8.2 mm de diá

STEPSTLGLB5 PARAMS
ESP32 Super Mini Enclosure - Right Half - Free CAD Model (STEP, STL) | TextoCAD