Brackets and mounts
ESP32-S3 4.0in Touch Phone Back Housing
- Bounding box
- 99 × 67.5 × 14.6 mm
- Engine
- 3D Printing B-rep
- Parameters
- 24
- Published
- November 18, 2026
Download
Free to download and use. See the terms.
The prompt
Use the uploaded photo of my actual ESP32-S3 4.0-inch 480×320 touchscreen board as the primary physical reference. Create a functional 3D-printable PHONE BACK HOUSING that the entire board shown in the photo fits inside. IMPORTANT: Do NOT redesign or rearrange the electronics. Keep the exact orientation and placement of the real board shown in the photo. The housing must: - Fit the complete ESP32-S3 touchscreen PCB inside - Follow the rectangular shape of the actual board - Have rounded phone-style outer corners - Leave approximately 0.5–1 mm clearance around the PCB - Include four internal mounting points that line up with the four mounting holes visible in the photo - Support the PCB from underneath without touching or pressing on electronic components - Leave clearance above all components - Leave the USB port on the LEFT side accessible from outside the phone - Leave the microSD card slot on the LOWER-RIGHT side accessible - Leave the side buttons accessible - Leave all required connectors accessible - Leave room for the display/touchscreen ribbon cable - Keep the back surface smooth and mostly flat - Make the walls strong enough for FDM printing - Avoid unnecessary supports and complicated geometry - Make the enclosure easy to print on an Entina Tina2C - Design it as a real mechanical enclosure, NOT a decorative 3D model The screen/display should face toward the FRONT of the finished phone. Create only the BACK HOUSING first. Before exporting, verify that: 1. The PCB fits inside the pocket. 2. The four mounting holes line up with the mounting posts. 3. The USB port can be plugged into from outside the case. 4. The microSD slot remains accessible. 5. No mounting post or wall interferes with any electronic component. 6. There is enough internal depth for the actual PCB and connectors. Export the finished model as an STL suitable for 3D printing. Use the uploaded photo as the reference for the board's orientation, mounting-hole locations, ports, buttons, and component placement. Do not guess these locations if they can be identified from the image.
Parameters
| Name | Value | Range |
|---|---|---|
| PCB length X | 94 mm | 60 – 110 |
| PCB width Y | 62.5 mm | 40 – 90 |
| PCB thickness | 1.6 mm | 1 – 4 |
| Mounting-hole inset from PCB X edge | 4 mm | 2 – 10 |
| Mounting-hole inset from PCB Y edge | 4 mm | 2 – 10 |
| USB port center Y | 5 mm | -20 – 20 |
| USB opening width Y | 13 mm | 6 – 20 |
| USB opening height Z | 7 mm | 4 – 12 |
| microSD opening center Y | -18 mm | -30 – 0 |
| microSD opening width Y | 16 mm | 8 – 24 |
| microSD opening height Z | 5 mm | 3 – 12 |
| Upper side-button center Y | 17 mm | -30 – 30 |
| Lower side-button center Y | -12 mm | -30 – 30 |
| Button opening width Y | 7 mm | 4 – 12 |
| Button opening height Z | 5 mm | 3 – 10 |
| PCB clearance per side | 0.5 mm | 0.2 – 2 |
| Wall thickness | 2 mm | 1.6 – 5 |
| Back floor thickness | 2.5 mm | 1.5 – 6 |
| PCB-to-floor clearance | 6.5 mm | 3 – 12 |
| Wall rim above PCB front | 4 mm | 0 – 8 |
| Phone-style outer corner radius | 8 mm | 4 – 20 |
| Mounting post diameter | 6 mm | 4 – 10 |
| M3 pilot hole diameter | 2.8 mm | 2 – 4.5 |
| Pilot hole depth | 5.5 mm | 3 – 8 |
Every value above is a live dimension. Open a model like this in the editor and each one becomes a slider you can drag before exporting.
More models
Browse the full gallery →UAV Ogive Nose Cone
Design a watertight, 3D-printable aerodynamic nose cone module for a fixed-wing tactical UAV, optimized for printing in Carbon Fiber Filled PETG (PETG-CF). The base of the nose con
Trumpet Lyre Mount Main Body
A single 3D mechanical CAD part for a trumpet music lyre mount (Main Body with Paddle). Geometry details: 1. A 18mm-wide semi-cylindrical clamp arc for a 28mm diameter cylinder, w
Flat-Strap Reel Spool
Create a 3D model of a custom flat-strap reel spool for a home plate housing cavity. Geometry: - A reel spool consisting of two parallel circular outer flanges connected by a cent
PET Recycling Kiosk Frame
Design a production-ready welded steel frame for an outdoor PET bottle recycling and animal feeding kiosk. Create ONLY the steel frame. Do not create covers, motors, tanks, electr
JZX100 Gas Cap Holder
can you make a gas cap holder for a jzx100 chaser. i want you to refer to the image and make a cad very close to the picture
Micro RC Airplane Frame
Create a lightweight 3D-printable indoor micro RC airplane frame. The fuselage is a hollow rectangular boom 200 mm long, 3 mm wide, and 3 mm tall, with an open U-shaped electronics
