Brackets and mounts
Electronics Enclosure with Standoffs and Cutouts
- Bounding box
- 100 × 70 × 30 mm
- Engine
- 3D Printing B-rep
- Parameters
- 17
- Published
- November 20, 2026
Download
Free to download and use. See the terms.
The prompt
"Create a rectangular electronics enclosure box measuring 100 mm length, 70 mm width, and 30 mm height, with 2.5 mm wall thickness and 4 mm rounded outer vertical corners. Inside the bottom floor, add four cylindrical PCB mounting standoffs of 6 mm outer diameter, 3 mm inner hole diameter, and 5 mm height, positioned 10 mm inward from each corner. On the front 70 mm wall, cut a rectangular USB power slot measuring 10 mm wide by 4 mm high centered 8 mm from the bottom. On the right 100 mm wall, cut two circular holes of 6 mm diameter spaced 20 mm apart for moisture sensor probe leads. On the left and right outer walls, add two flat mounting tabs 15 mm wide and 3 mm thick with 4 mm screw holes."
Parameters
| Name | Value | Range |
|---|---|---|
| Length | 100 mm | 20 – 300 |
| Width | 70 mm | 20 – 200 |
| Height | 30 mm | 5 – 120 |
| Wall thickness | 2.5 mm | 0.8 – 6 |
| Outer corner radius | 4 mm | 1 – 20 |
| Standoff OD | 6 mm | 3 – 12 |
| Standoff hole ID | 3 mm | 1 – 8 |
| Standoff height | 5 mm | 2 – 15 |
| Standoff inset from walls | 10 mm | 5 – 30 |
| USB slot width | 10 mm | 4 – 20 |
| USB slot height | 4 mm | 2 – 10 |
| USB slot center from bottom | 8 mm | 2 – 20 |
| Sensor hole diameter | 6 mm | 2 – 12 |
| Sensor hole spacing | 20 mm | 4 – 40 |
| Tab width | 15 mm | 8 – 30 |
| Tab thickness | 3 mm | 1.2 – 8 |
| Tab screw hole diameter | 4 mm | 3 – 6 |
Every value above is a live dimension. Open a model like this in the editor and each one becomes a slider you can drag before exporting.
More models
Browse the full gallery →UAV Ogive Nose Cone
Design a watertight, 3D-printable aerodynamic nose cone module for a fixed-wing tactical UAV, optimized for printing in Carbon Fiber Filled PETG (PETG-CF). The base of the nose con
Trumpet Lyre Mount Main Body
A single 3D mechanical CAD part for a trumpet music lyre mount (Main Body with Paddle). Geometry details: 1. A 18mm-wide semi-cylindrical clamp arc for a 28mm diameter cylinder, w
Flat-Strap Reel Spool
Create a 3D model of a custom flat-strap reel spool for a home plate housing cavity. Geometry: - A reel spool consisting of two parallel circular outer flanges connected by a cent
PET Recycling Kiosk Frame
Design a production-ready welded steel frame for an outdoor PET bottle recycling and animal feeding kiosk. Create ONLY the steel frame. Do not create covers, motors, tanks, electr
JZX100 Gas Cap Holder
can you make a gas cap holder for a jzx100 chaser. i want you to refer to the image and make a cad very close to the picture
Micro RC Airplane Frame
Create a lightweight 3D-printable indoor micro RC airplane frame. The fuselage is a hollow rectangular boom 200 mm long, 3 mm wide, and 3 mm tall, with an open U-shaped electronics
