Fittings and adapters
Compact Harmonic Drive Reducer (Robot Joint)
- Bounding box
- 476.0 × 58.7 × 34.5 mm
- Engine
- Precision B-rep
- Parameters
- 56
- Published
- November 16, 2026
Download
Free to download and use. See the terms.
The prompt
请设计一个用于机器人机械臂关节的紧凑型谐波减速器(Harmonic Drive Reducer)三维 CAD 模型。 **一、整体尺寸与结构要求** - 减速器主体外径约 50mm,目标控制在 45–50mm 范围内。 - 总成最大轴向厚度不超过 50mm,包含安装法兰和支撑脚。 - 整体结构紧凑、对称,适合安装在机器人机械臂关节位置。 - 允许在主体外壳底部或侧面增加若干安装支撑脚,以提高安装稳定性。 - 支撑脚应与主体结构可靠连接,并预留螺栓安装孔。 **二、核心机械结构** 请按照典型谐波减速器的工作原理,设计以下主要部件: 1. 刚轮(Circular Spline):环形刚性齿圈,内侧具有均匀分布的内齿。 2. 柔轮(Flexspline):薄壁杯形弹性齿轮,外侧具有与刚轮啮合的外齿。 3. 波发生器(Wave Generator):由椭圆形凸轮和柔性轴承组成,用于使柔轮产生椭圆形弹性变形。 4. 输出法兰(Output Flange):与柔轮连接,用于输出减速后的旋转运动。 5. 输入轴(Input Shaft):与波发生器连接,用于输入高速旋转运动。 6. 轴承及支撑结构:合理布置轴承、定位结构和连接件,保证各旋转部件的同轴度及支撑稳定性。 **三、安装结构** - 主体设计合理的输入端和输出端接口。 - 设置底部安装法兰或 3–4 个对称分布的支撑脚。 - 支撑脚设置标准化螺栓通孔,方便固定在机器人机械臂连接板上。 - 输出法兰预留中心通孔及周向均匀分布的螺栓孔,用于连接机器人关节输出端。 - 所有安装结构应避免与旋转部件发生干涉。 **四、几何与工程设计要求** - 各部件应具有明确的结构层次和装配关系。 - 核心旋转部件应保持同轴布置。 - 柔轮采用薄壁杯形结构,体现谐波减速器特有的弹性变形结构。 - 刚轮与柔轮采用合理的齿轮啮合关系。 - 壳体应具有足够的壁厚和结构刚度。 - 螺栓孔、轴承座、定位台阶和连接法兰等细节应体现真实机械设计特征。 - 避免零件之间出现明显几何干涉。 **五、CAD 输出要求** - 生成完整的三维装配体,而不是单一外观模型。 - 各主要零件独立建模,具有清晰的零件名称和装配层级。 - 提供可编辑的参数化特征树。 - 输出整体装配模型及零件分解模型。 - 提供 STEP 格式的三维模型文件。 - 同时生成等轴测视图、正视图、侧视图和爆炸装配视图。 - 在模型中标注整体外径、总厚度、安装孔位置及主要连接尺寸。 **最终目标:** 生成一个外径约 50mm、总厚度不超过 50mm、带有稳固安装支撑脚的紧凑型机器人机械臂关节谐波减速器。模型应具有清晰、可信的机械结构和完整的装配关系,外观符合真实工业谐波减速器的设计风格。
Parameters
| Name | Value | Range |
|---|---|---|
| Exploded Layout Gap | 12 mm | 2 – 60 |
| Housing Outer Diameter | 50 mm | 40 – 70 |
| Housing Axial Length | 24 mm | 12 – 40 |
| Housing Wall Thickness | 3 mm | 1.5 – 6 |
| Mounting Foot Count | 3 pcs | 3 – 6 |
| Foot Width | 10 mm | 5 – 20 |
| Foot Thickness | 6 mm | 2 – 12 |
| Foot Radial Extension | 6 mm | 2 – 16 |
| Foot Bolt Hole Dia (M4) | 4.5 mm | 2.5 – 8 |
| Circular Spline OD | 46 mm | 30 – 70 |
| Circular Spline Root Dia | 40 mm | 25 – 64 |
| Circular Spline Width | 9 mm | 4 – 20 |
| Circular Spline Teeth | 62 pcs | 40 – 100 |
| Internal Tooth Depth | 1 mm | 0.4 – 2.5 |
| Flexspline Rim OD | 36 mm | 22 – 60 |
| Cup Wall Thickness | 0.8 mm | 0.4 – 3 |
| Cup Length | 18 mm | 8 – 35 |
| External Tooth Depth | 0.8 mm | 0.4 – 2.5 |
| Flexspline Teeth | 60 pcs | 38 – 98 |
| Flexspline Flange OD | 44 mm | 28 – 66 |
| Flexspline Flange Thickness | 2.5 mm | 1 – 8 |
| Diaphragm Thickness | 2 mm | 0.8 – 6 |
| Flange Bolt Count | 6 pcs | 3 – 12 |
| Flange Bolt PCD | 36 mm | 20 – 60 |
| Flange Bolt Hole Dia (M3) | 3.2 mm | 2 – 6 |
| Cam Major Axis Dia | 32 mm | 18 – 50 |
| Cam Minor Axis Dia | 28 mm | 16 – 46 |
| Cam Axial Width | 7 mm | 3 – 16 |
| Cam Shaft Bore | 8 mm | 4 – 16 |
| Flex Bearing OD | 34 mm | 20 – 50 |
| Flex Bearing ID | 28 mm | 16 – 46 |
| Flex Bearing Width | 6.5 mm | 3 – 16 |
| Output Flange OD | 46 mm | 30 – 70 |
| Output Flange Thickness | 7 mm | 3 – 15 |
| Center Through Hole | 12 mm | 4 – 30 |
| Output Bolt Count | 6 pcs | 3 – 12 |
| Output Bolt PCD | 36 mm | 20 – 60 |
| Output Bolt Hole Dia (M3) | 3.2 mm | 2 – 6 |
| Output Bearing OD | 44 mm | 26 – 66 |
| Output Bearing ID | 36 mm | 20 – 60 |
| Output Bearing Width | 8 mm | 3 – 18 |
| Input Shaft Diameter | 8 mm | 4 – 16 |
| Input Shaft Length | 32 mm | 15 – 60 |
| Rear Flat Length | 8 mm | 2 – 20 |
| Rear Flat Depth | 0.7 mm | 0.2 – 2.5 |
| Input Bearing OD | 16 mm | 10 – 30 |
| Input Bearing ID | 8 mm | 4 – 20 |
| Input Bearing Width | 5 mm | 2 – 12 |
| Rear Cover OD | 42 mm | 26 – 64 |
| Rear Cover Thickness | 5 mm | 2 – 12 |
| Shaft Through Hole | 10 mm | 6 – 20 |
| Bearing Seat Dia | 16 mm | 10 – 28 |
| Bearing Seat Depth | 3.5 mm | 1 – 6 |
| Cover Screw Count | 4 pcs | 3 – 8 |
| Cover Screw PCD | 34 mm | 18 – 56 |
| Cover Screw Hole Dia (M3) | 3.2 mm | 2 – 6 |
Every value above is a live dimension. Open a model like this in the editor and each one becomes a slider you can drag before exporting.
More models
Browse the full gallery →SM1 to RMS Thread Adapter
thorlabs SM1A3 adapter has external SM1 (1.035"-40) threading and internal RMS (0.800"-36) threading.
Under Door Split AC Exhaust Adapter
I have a portable AC unit I want to use in my garage. i want to use an under the door style adapter. Source Image 1 (Front - under door rectangular): Height is 1.5 inch (convert
Inline Hose Adapter with Sensor Boss
Create a cylindrical inline hose adapter tube for automotive cooling. Total length is 65mm. The main central body is a cylinder with an outer diameter of 20mm and a length of 25mm.
MCR Building Cable Entry Fitting
an you help me to desigen firfitting for mcr buillding for 10 mw solar power plant
Garage Door Exhaust Hose Adapter
I have a portable AC unit I want to use in my garage. I will use a board as an insert at the bottom of the garage door, and cut 2 holes for the 2 exhaust hoses. The adapter it came
US Coin Organizer
make a mathamatically acurate exact fitting us coin organiser please
