Brackets and mounts
Clamshell Pen Body (LED / Reed / G2)
- Bounding box
- 140 × 31.5 × 26 mm
- Engine
- 3D Printing B-rep
- Parameters
- 19
- Published
- November 20, 2026
Download
Free to download and use. See the terms.
The prompt
1. Pilot G2 Ink Tube - Tunnel: 6.5mm wide, ~111mm long - Tip hole: 2.6mm at the nose so the tip pokes out 2. Reed Switch Slot - Groove: 2.5mm x 2.5mm x 24mm long (extra length is for the metal legs) - Run it parallel right next to the ink tunnel, leaving the wall between them super thin (0.8mm to 1mm) so the magnet triggers cleanly - Line the top of the glass up around 40–45mm back from the pen tip 3. Red LED Hole - 3.3mm hole on the upper front, above where your fingers grip so your hand doesn't block the light 4. Battery Holder Pocket - 36.5mm x 26.5mm x 7mm flat cutout up in that top pod - Cut a little window on the side or back so you can still reach the tiny on/off slide switch 5. Wire Channels - Carve out little 2.5mm x 2.5mm trenches connecting the battery pocket -> LED hole -> reed switch slot so wires don't get pinched when you close the two halves Quick Slicer Settings - Filament: Standard PLA is totally fine (PETG if they want a bit more flex) - Nozzle / Layers: 0.4mm nozzle, 0.16mm or 0.20mm layer height - Strength: 3 walls and 15–20% infill
Parameters
| Name | Value | Range |
|---|---|---|
| Pen length | 140 mm | 100 – 220 |
| Main barrel diameter | 20 mm | 14 – 40 |
| Wall/minimum clearance | 2 mm | 0.8 – 6 |
| Ink-tube tunnel width | 6.5 mm | 4 – 10 |
| Ink-tube tunnel length | 111 mm | 80 – 150 |
| Tip opening diameter | 2.6 mm | 1.5 – 4 |
| Reed-switch slot width | 2.5 mm | 1.5 – 4 |
| Reed-switch slot height | 2.5 mm | 1.5 – 4 |
| Reed-switch slot length | 24 mm | 10 – 40 |
| Reed switch centre from pen tip | 42 mm | 30 – 70 |
| Reed to tunnel wall | 0.8 mm | 0.6 – 2 |
| LED hole diameter | 3.3 mm | 2 – 6 |
| LED hole centre from pen tip | 34 mm | 20 – 80 |
| Battery pocket length | 36.5 mm | 20 – 60 |
| Battery pocket width | 26.5 mm | 10 – 40 |
| Battery pocket height | 7 mm | 3 – 15 |
| Battery pocket centre X from pen middle | 20 mm | -10 – 60 |
| Wire channel width | 2.5 mm | 1.5 – 4 |
| Wire channel height | 2.5 mm | 1.5 – 4 |
Every value above is a live dimension. Open a model like this in the editor and each one becomes a slider you can drag before exporting.
More models
Browse the full gallery →UAV Ogive Nose Cone
Design a watertight, 3D-printable aerodynamic nose cone module for a fixed-wing tactical UAV, optimized for printing in Carbon Fiber Filled PETG (PETG-CF). The base of the nose con
Trumpet Lyre Mount Main Body
A single 3D mechanical CAD part for a trumpet music lyre mount (Main Body with Paddle). Geometry details: 1. A 18mm-wide semi-cylindrical clamp arc for a 28mm diameter cylinder, w
Flat-Strap Reel Spool
Create a 3D model of a custom flat-strap reel spool for a home plate housing cavity. Geometry: - A reel spool consisting of two parallel circular outer flanges connected by a cent
PET Recycling Kiosk Frame
Design a production-ready welded steel frame for an outdoor PET bottle recycling and animal feeding kiosk. Create ONLY the steel frame. Do not create covers, motors, tanks, electr
JZX100 Gas Cap Holder
can you make a gas cap holder for a jzx100 chaser. i want you to refer to the image and make a cad very close to the picture
Micro RC Airplane Frame
Create a lightweight 3D-printable indoor micro RC airplane frame. The fuselage is a hollow rectangular boom 200 mm long, 3 mm wide, and 3 mm tall, with an open U-shaped electronics
