Brackets and mounts
Chassis Base Plate
- Bounding box
- 140 × 220 × 19 mm
- Engine
- 3D Printing B-rep
- Parameters
- 37
- Published
- November 17, 2026
Download
Free to download and use. See the terms.
The prompt
Create a rectangular chassis base plate 220 mm long, 140 mm wide, and 4 mm thick with 8 mm filleted corners. 1. Near the front edge (30 mm from front), cut a centered rectangular pocket 41 mm wide by 20.5 mm long through the plate, surrounded by four 2.5 mm diameter mounting holes spaced 49.5 mm by 10 mm for an MG996R servo. 2. In the center section (95 mm from front), add four 3.2 mm through-holes arranged in a 37 mm by 37 mm square on the left side for an L298N driver, and four 2.2 mm through-holes arranged in a 50 mm by 23 mm rectangle on the right side for an ESP32 board. 3. Behind the electronics (155 mm from front), add two 3.2 mm centered holes spaced 54 mm apart along the width for a 2x 18650 battery holder. 4. At 165 mm from front, cut a centered rectangular pocket 23 mm long by 12.2 mm wide with two 2.0 mm mounting holes spaced 27.5 mm apart for an SG90 lifting servo. 5. On the top surface at the two rear corners, extrude two vertical hinge lugs 15 mm tall, 12 mm long, and 5 mm thick, each with a 4.2 mm horizontal through-hole centered 10 mm above the plate. 6. Along both left and right edges, add four pairs of 3.2 mm mounting holes (spaced 14 mm apart per pair) at 40 mm and 170 mm from the front to bolt motor brackets underneath.
Parameters
| Name | Value | Range |
|---|---|---|
| Plate length | 220 mm | 100 – 400 |
| Plate width | 140 mm | 50 – 300 |
| Plate thickness | 4 mm | 2 – 10 |
| Corner fillet radius | 8 mm | 1 – 20 |
| Servo center from front | 30 mm | 10 – 100 |
| Pocket width across X | 41 mm | 10 – 80 |
| Pocket length along Y | 20.5 mm | 5 – 50 |
| Mounting hole diameter | 2.5 mm | 1 – 6 |
| Hole spacing across X | 49.5 mm | 10 – 100 |
| Hole spacing along Y | 10 mm | 5 – 50 |
| Electronics center from front | 95 mm | 20 – 180 |
| L298N center X | -32 mm | -60 – 60 |
| L298N hole diameter | 3.2 mm | 1 – 6 |
| L298N hole square spacing | 37 mm | 10 – 80 |
| ESP32 center X | 30 mm | -60 – 60 |
| ESP32 hole diameter | 2.2 mm | 1 – 6 |
| ESP32 X spacing | 50 mm | 10 – 100 |
| ESP32 Y spacing | 23 mm | 5 – 50 |
| Battery holder center from front | 155 mm | 50 – 200 |
| Battery hole diameter | 3.2 mm | 1 – 6 |
| Battery hole spacing across X | 54 mm | 10 – 120 |
| Lift servo center from front | 165 mm | 20 – 210 |
| Pocket width across X | 12.2 mm | 5 – 40 |
| Pocket length along Y | 23 mm | 5 – 60 |
| Mounting hole diameter | 2 mm | 0.8 – 5 |
| Mounting hole spacing across X | 27.5 mm | 5 – 60 |
| Lug height above plate | 15 mm | 5 – 40 |
| Lug length along Y | 12 mm | 4 – 40 |
| Lug thickness along X | 5 mm | 2 – 20 |
| Hinge pin hole diameter | 4.2 mm | 1 – 10 |
| Hole center above plate top | 10 mm | 3 – 30 |
| Lug center X offset | 59 mm | 0 – 80 |
| Edge hole inset from side | 10 mm | 3 – 25 |
| Front bracket hole center from front | 40 mm | 5 – 100 |
| Rear bracket hole center from front | 170 mm | 100 – 215 |
| Spacing within each pair | 14 mm | 4 – 40 |
| Bracket hole diameter | 3.2 mm | 1 – 6 |
Every value above is a live dimension. Open a model like this in the editor and each one becomes a slider you can drag before exporting.
More models
Browse the full gallery →UAV Ogive Nose Cone
Design a watertight, 3D-printable aerodynamic nose cone module for a fixed-wing tactical UAV, optimized for printing in Carbon Fiber Filled PETG (PETG-CF). The base of the nose con
Trumpet Lyre Mount Main Body
A single 3D mechanical CAD part for a trumpet music lyre mount (Main Body with Paddle). Geometry details: 1. A 18mm-wide semi-cylindrical clamp arc for a 28mm diameter cylinder, w
Flat-Strap Reel Spool
Create a 3D model of a custom flat-strap reel spool for a home plate housing cavity. Geometry: - A reel spool consisting of two parallel circular outer flanges connected by a cent
PET Recycling Kiosk Frame
Design a production-ready welded steel frame for an outdoor PET bottle recycling and animal feeding kiosk. Create ONLY the steel frame. Do not create covers, motors, tanks, electr
JZX100 Gas Cap Holder
can you make a gas cap holder for a jzx100 chaser. i want you to refer to the image and make a cad very close to the picture
Compression Testing Tower
The central square tower contains a 450 mm lead screw and a parallel 16 mm diameter steel guide shaft. Both are securely supported by bearings. A horizontal sliding block spans be
