Brackets and mounts
Bow Sight Linkage Assembly
- Bounding box
- 48.7 × 130.8 × 125.5 mm
- Engine
- 3D Printing B-rep
- Parameters
- 39
- Published
- November 16, 2026
Download
Free to download and use. See the terms.
The prompt
Create an assembly model in millimeters, with all parts positioned together on one origin. Origin is the center of the upper pin. X axis runs along the upper pin, Y axis runs toward the archer, Z axis runs up. Keep each part as a separate solid in the same model, in its stated position, do not fuse them together. 1. Mounting bracket: flat plate 124.7 mm long, 9 mm wide, 4 mm thick, X 41.65 to 45.65, Y -6 to 118.7, Z -4.5 to 4.5. Cut an 8.2 mm diameter through-hole centered at Y 0, Z 0. Trim the far end to a circular arc of radius 118.7 mm centered on that hole. 2. Upper pin: 33.93 mm long along X, centered at Y 0, Z 0, X 20.40 to 54.33. First 25.25 mm is a round shaft 8 mm diameter. Remaining 8.68 mm is a hexagonal shaft 8 mm vertex-to-vertex. Cut a 4.4 mm diameter through-bore along its full length. 3. Yardage slider arm: flat arm 129.2 mm long, 9 mm wide, 5.5 mm thick, X 45.65 to 51.15, Y -4.5 to 124.7, Z -4.5 to 4.5. Cut a hexagonal through-hole 8.2 mm vertex-to-vertex centered at Y 0, Z 0, fitting the hex end of the upper pin. Cut a round through-hole 4.4 mm diameter centered at Y 118.7, Z 0. 4. Lower pin: hollow tube 21.05 mm long along X, X 20.40 to 41.45, centered at Y 0, Z -55.24, 8 mm outside diameter, 4.4 mm through-bore. 5. Two linkage arms: each flat arm 112.2 mm long, 13.6 mm wide, 4 mm thick, with two 4.4 mm diameter through-holes 6.1 mm from each end. Place the first arm with its first hole concentric with the upper pin at Y 0, Z 0, and its second hole at Y 100, Z 0. Place the second arm with its first hole concentric with the lower pin at Y 0, Z -55.24, and its second hole at Y 100, Z -55.24. 6. Optic footprint plate: flat plate 48.3 mm long, 35.6 mm wide, 3.2 mm thick, placed at the far ends of the two linkage arms, spanning between them, centered at Y 100, Z -27.6. Cut two 3.2 mm diameter through-holes spaced 14.15 mm apart, centered on the plate. Use millimeters.
Parameters
| Name | Value | Range |
|---|---|---|
| Bracket -X face position | 41.65 mm | 0 – 100 |
| Bracket thickness along X | 4 mm | 2 – 10 |
| Bracket near end, Y | -6 mm | -30 – 30 |
| Bracket length along Y | 124.7 mm | 40 – 200 |
| Bracket width along Z | 9 mm | 4 – 20 |
| Pivot through-hole diameter | 8.2 mm | 4 – 12 |
| Far-end trim arc radius | 118.7 mm | 60 – 200 |
| Pin outside diameter | 8 mm | 4 – 12 |
| Pin through-bore diameter | 4.4 mm | 2 – 8 |
| Hex shaft, vertex-to-vertex | 8 mm | 4 – 14 |
| Upper pin -X end | 20.4 mm | 0 – 60 |
| Upper pin round section length | 25.25 mm | 5 – 60 |
| Upper pin hex section length | 8.68 mm | 2 – 25 |
| Lower pin -X end | 20.4 mm | 0 – 60 |
| Lower pin length | 21.05 mm | 3 – 80 |
| Lower pin axis height, Z | -55.24 mm | -120 – -5 |
| Slider arm -X face | 45.65 mm | 0 – 100 |
| Slider arm thickness along X | 5.5 mm | 2 – 12 |
| Slider arm near end, Y | -4.5 mm | -30 – 30 |
| Slider arm length along Y | 129.2 mm | 40 – 220 |
| Slider arm width along Z | 9 mm | 4 – 20 |
| Hex hole, vertex-to-vertex | 8.2 mm | 4 – 14 |
| Round hole diameter | 4.4 mm | 2 – 10 |
| Round hole Y position | 118.7 mm | 20 – 220 |
| Arm length | 112.2 mm | 40 – 200 |
| Arm width along Z | 13.6 mm | 5 – 30 |
| Arm thickness along X | 4 mm | 2 – 10 |
| Arm pivot hole diameter | 4.4 mm | 2 – 10 |
| Hole inset from each end | 6.1 mm | 2 – 30 |
| Arm -X face | 21.4 mm | 0 – 80 |
| Hole-to-hole distance along Y | 100 mm | 20 – 180 |
| Plate height along Z | 48.3 mm | 15 – 90 |
| Plate width along X | 35.6 mm | 15 – 90 |
| Plate thickness along Y | 3.2 mm | 1.2 – 10 |
| Plate centre, X | 23.4 mm | -40 – 80 |
| Plate centre, Y | 100 mm | 20 – 200 |
| Plate centre, Z | -27.6 mm | -120 – -5 |
| Mounting hole diameter | 3.2 mm | 1.5 – 8 |
| Mounting hole spacing | 14.15 mm | 4 – 40 |
Every value above is a live dimension. Open a model like this in the editor and each one becomes a slider you can drag before exporting.
More models
Browse the full gallery →UAV Ogive Nose Cone
Design a watertight, 3D-printable aerodynamic nose cone module for a fixed-wing tactical UAV, optimized for printing in Carbon Fiber Filled PETG (PETG-CF). The base of the nose con
Trumpet Lyre Mount Main Body
A single 3D mechanical CAD part for a trumpet music lyre mount (Main Body with Paddle). Geometry details: 1. A 18mm-wide semi-cylindrical clamp arc for a 28mm diameter cylinder, w
Flat-Strap Reel Spool
Create a 3D model of a custom flat-strap reel spool for a home plate housing cavity. Geometry: - A reel spool consisting of two parallel circular outer flanges connected by a cent
PET Recycling Kiosk Frame
Design a production-ready welded steel frame for an outdoor PET bottle recycling and animal feeding kiosk. Create ONLY the steel frame. Do not create covers, motors, tanks, electr
JZX100 Gas Cap Holder
can you make a gas cap holder for a jzx100 chaser. i want you to refer to the image and make a cad very close to the picture
Compression Testing Tower
The central square tower contains a 450 mm lead screw and a parallel 16 mm diameter steel guide shaft. Both are securely supported by bearings. A horizontal sliding block spans be
