Enclosures and housings
Black Rear Chassis Tub
- Bounding box
- 62.0 × 102.0 × 18.5 mm
- Engine
- Precision B-rep
- Parameters
- 38
- Published
- November 18, 2026
Download
Free to download and use. See the terms.
The prompt
Part 2: Black Rear Chassis Tub (with Recessed Mortise Slots & Ports) Prompt: Create a hollow 3D-printable electronics enclosure rear tub in millimeters. The outer profile matches a vertical rounded rectangle measuring 62.0 mm wide (X: -31 to +31), 102.0 mm tall (Y: -51 to +51), and 18.5 mm high (Z: 0 to +18.5), with 6.0 mm outer corner fillets. Remove a top-right corner L-notch measuring 13.5 mm wide (X: +17.5 to +31.0) by 25.0 mm tall (Y: +26.0 to +51.0) from Z = +12.5 mm to Z = +18.5 mm, leaving a solid horizontal step platform at Z = +12.5 mm for a rotary dial. Drill a 7.4 mm diameter vertical through-hole in the center of this step platform at (X=+23.25, Y=+38.5) for an EC11 rotary encoder shaft. Hollow out the interior cavity starting from Z = +2.4 mm (solid bottom floor) up to Z = +18.5 mm, maintaining a 4.6 mm thick outer rim wall (X and Y inner walls inset 4.6 mm from the outer perimeter) so there is room for perimeter mortise slots. Cut 4 recessed mortise slots downward into the top rim face (Z = +18.5 mm down to Z = +13.6 mm, depth 4.9 mm) centered 3.0 mm inset from the outer perimeter walls, each widened by +0.30 mm (0.15 mm clearance per side) over the mating tenons: Left vertical slot: 1.7 mm wide (X), 76.3 mm long (Y), centered at (X=-28.0, Y=-4.0). Right lower vertical slot: 1.7 mm wide (X), 57.3 mm long (Y), centered at (X=+28.0, Y=-14.5). Bottom horizontal slot: 40.3 mm long (X), 1.7 mm wide (Y), centered at (X=0.0, Y=-48.0). Top horizontal slot: 30.8 mm long (X), 1.7 mm wide (Y), centered at (X=-6.75, Y=+48.0). Cut the following port openings through the outer walls: Top wall (Y = +51.0 mm): A 6.5 mm diameter circular hole centered at (X=-16.0, Z=+9.0) for a 3.5mm audio jack, and a stadium-shaped USB-C slot 9.6 mm wide by 3.6 mm tall centered at (X=-2.0, Z=+8.5). Left wall (X = -31.0 mm): A rectangular slide-switch cutout 8.2 mm along Y by 4.2 mm along Z, centered at (Y=+18.0, Z=+9.0). Top-left corner strap lug: A 3.8 mm diameter vertical through-hole from Z = 0 to Z = +18.5 mm centered at (X=-26.5, Y=+46.5).
Parameters
| Name | Value | Range |
|---|---|---|
| Outer Width (X) | 62 mm | 30 – 200 |
| Outer Height (Y) | 102 mm | 40 – 250 |
| Tub Height (Z) | 18.5 mm | 6 – 60 |
| Outer Corner Fillet | 6 mm | 0.5 – 15 |
| Rim Wall Thickness | 4.6 mm | 1.5 – 12 |
| Bottom Floor Thickness | 2.4 mm | 0.6 – 10 |
| L-Notch Width (X) | 13.5 mm | 0 – 50 |
| L-Notch Length (Y) | 25 mm | 0 – 80 |
| Step Platform Height (Z) | 12.5 mm | 3 – 40 |
| Encoder Shaft Hole Dia | 7.4 mm | 3 – 20 |
| Encoder Hole X | 23.25 mm | -60 – 60 |
| Encoder Hole Y | 38.5 mm | -100 – 100 |
| Mortise Slot Width | 1.7 mm | 0.5 – 6 |
| Mortise Slot Depth | 4.9 mm | 0.5 – 10 |
| Slot Inset From Perimeter | 3 mm | 1 – 15 |
| Left Slot Length | 76.3 mm | 5 – 140 |
| Left Slot Center Y | -4 mm | -100 – 100 |
| Right Slot Length | 57.3 mm | 5 – 140 |
| Right Slot Center Y | -14.5 mm | -100 – 100 |
| Bottom Slot Length | 40.3 mm | 5 – 140 |
| Bottom Slot Center X | 0 mm | -100 – 100 |
| Top Slot Length | 30.8 mm | 5 – 140 |
| Top Slot Center X | -6.75 mm | -100 – 100 |
| Audio Jack Hole Dia | 6.5 mm | 2 – 15 |
| Audio Jack Hole X | -16 mm | -80 – 80 |
| Audio Jack Hole Z | 9 mm | 1 – 40 |
| USB-C Slot Width (X) | 9.6 mm | 3 – 25 |
| USB-C Slot Height (Z) | 3.6 mm | 1 – 12 |
| USB-C Slot Center X | -2 mm | -80 – 80 |
| USB-C Slot Center Z | 8.5 mm | 1 – 40 |
| Slide Switch Cutout (Y) | 8.2 mm | 2 – 25 |
| Slide Switch Cutout (Z) | 4.2 mm | 1 – 15 |
| Slide Switch Center Y | 18 mm | -100 – 100 |
| Slide Switch Center Z | 9 mm | 1 – 40 |
| Strap Lug Hole Dia | 3.8 mm | 1 – 10 |
| Strap Lug Hole X | -26.5 mm | -60 – 60 |
| Strap Lug Hole Y | 46.5 mm | -100 – 100 |
| Lug Boss Pad Around Hole | 0.9 mm | 0.2 – 4 |
Every value above is a live dimension. Open a model like this in the editor and each one becomes a slider you can drag before exporting.
More models
Browse the full gallery →Cylindrical Stainless Steel Basket with Folding Handles
Design a cylindrical 304 stainless steel basket with an outer diameter of 200 mm and height of 250 mm. The basket has solid side walls with no perforations. The bottom plate contai
Lego 1x4 Technic Brick
Create a precise 3D CAD model of a single 1x4 Lego Technic-compatible brick designed for STEM robotics. The main rectangular body must have exact dimensions: 31.8 mm in length, 7.8
Immersion Cooling Enclosure
Design a sealed high-pressure dielectric immersion cooling enclosure for cylindrical battery cells. Internal cavity dimensions: 540mm length, 360mm width, 160mm height with 6mm wal
Simple BWB with Propulsion Tube
Prompt: "A simple, solid Blended Wing Body (BWB) flying wing. Dimensions: wingspan 6.5 meters, center chord 1.53 meters, root thickness 35 centimeters, tapering to 15 centimeters a
Engranaje recto 50 dientes, módulo 2
Engranaje recto de 50 dientes, diámetro exterior 104 mm, diámetro de raíz 95 mm, espesor 10 mm y ángulo de presión 20°. Crear como sólido 3D con un agujero central de 8.2 mm de diá
G+1 Party Hall Structural Shell
G+1 Party Hall – AutoCAD Design Prompt Design a G+1 RCC-framed Party Hall in AutoCAD with detailed Ground Floor Plan, First Floor Plan, and all-side elevations (front, rear, left
