Enclosures and housings
BirdID Enclosure
- Bounding box
- 132.0 × 117.0 × 46.5 mm
- Engine
- Precision B-rep
- Parameters
- 56
- Published
- October 28, 2026
Download
Free to download and use. See the terms.
The prompt
Adjusted BirdID Enclosure: view=0
Parameters
| Name | Value | Range |
|---|---|---|
| View (0 assembled, 1 exploded, 2 body, 3 lid, 4 tray, 5 mic plate) | 0 | 0 – 5 |
| Cavity length (horizontal) | 110 mm | 90 – 160 |
| Cavity width (vertical) | 95 mm | 80 – 140 |
| Cavity depth | 35 mm | 28 – 60 |
| Wall thickness | 3 mm | 2 – 5 |
| Floor thickness | 3 mm | 2 – 5 |
| Cavity corner radius | 3 mm | 1 – 8 |
| Lid thickness | 3 mm | 2 – 5 |
| Inner seal land | 2 mm | 1 – 4 |
| Gasket groove width | 2.6 mm | 1.5 – 4 |
| Gasket groove depth | 1.5 mm | 0.8 – 3 |
| Outer seal land | 2.4 mm | 1 – 5 |
| Flange height | 6 mm | 4 – 10 |
| Lid alignment lip height | 3 mm | 1.5 – 6 |
| Lid alignment lip thickness | 2 mm | 1.2 – 3 |
| Lip clearance per side | 0.3 mm | 0.1 – 0.8 |
| Screw offset from cavity corner | 6.5 mm | 5 – 12 |
| Screw boss diameter | 9 mm | 7 – 14 |
| Boss hole dia (M3 heat-set insert) | 4 mm | 2.4 – 5.5 |
| Blind boss hole depth | 10 mm | 5 – 20 |
| Lid screw clearance hole | 3.4 mm | 2.5 – 5 |
| Rear base thickness | 5.5 mm | 4.5 – 10 |
| Strap opening width | 22 mm | 15 – 40 |
| Strap opening height | 3 mm | 2 – 6 |
| Strap tunnel offset from centre | 25 mm | 14 – 40 |
| Tray length | 73 mm | 60 – 100 |
| Tray width | 30 mm | 26 – 45 |
| Tray thickness | 2.5 mm | 1.6 – 4 |
| Tray floor boss height | 3 mm | 2 – 8 |
| Tray screw pilot dia | 2.5 mm | 1.8 – 3.2 |
| Board stack length | 52.3 mm | 45 – 60 |
| Board stack width | 22.9 mm | 18 – 28 |
| Board start from tray end | 10 mm | 6 – 20 |
| PCB standoff (land) height | 5 mm | 3 – 10 |
| Drillable land length | 7.5 mm | 4 – 12 |
| Battery space length | 70 mm | 50 – 80 |
| Battery space width | 56 mm | 40 – 60 |
| Strap post thickness | 5 mm | 3 – 8 |
| Strap post height | 14 mm | 8 – 20 |
| Battery strap slot width | 22 mm | 10 – 30 |
| Battery strap slot height | 3.5 mm | 2 – 6 |
| Gap wall to left post | 6 mm | 3 – 12 |
| Mic port position (from centre) | 37 mm | -35 – 38 |
| Mic port height above floor | 18 mm | 10 – 24 |
| Acoustic port diameter | 2 mm | 1 – 4 |
| Wind-cover rim OD | 16 mm | 12 – 22 |
| Membrane seat diameter | 12 mm | 8 – 18 |
| Rim height | 3 mm | 1.5 – 6 |
| Mic plate boss length | 5 mm | 3 – 10 |
| Mic gasket thickness (compressed) | 1.5 mm | 0.5 – 3 |
| Mic plate screw offset | 9 mm | 8 – 12 |
| Mic slot adjust (each way) | 2.5 mm | 0.5 – 4 |
| Mic plate width | 30 mm | 26 – 36 |
| Mic plate height | 18 mm | 14 – 24 |
| Mic plate thickness | 2.5 mm | 1.6 – 4 |
| Mic plate sound hole | 3 mm | 1.5 – 6 |
Every value above is a live dimension. Open a model like this in the editor and each one becomes a slider you can drag before exporting.
More models
Browse the full gallery →Cylindrical Stainless Steel Basket with Folding Handles
Design a cylindrical 304 stainless steel basket with an outer diameter of 200 mm and height of 250 mm. The basket has solid side walls with no perforations. The bottom plate contai
Immersion Cooling Enclosure
Design a sealed high-pressure dielectric immersion cooling enclosure for cylindrical battery cells. Internal cavity dimensions: 540mm length, 360mm width, 160mm height with 6mm wal
Simple BWB with Propulsion Tube
Prompt: "A simple, solid Blended Wing Body (BWB) flying wing. Dimensions: wingspan 6.5 meters, center chord 1.53 meters, root thickness 35 centimeters, tapering to 15 centimeters a
Engranaje recto 50 dientes, módulo 2
Engranaje recto de 50 dientes, diámetro exterior 104 mm, diámetro de raíz 95 mm, espesor 10 mm y ángulo de presión 20°. Crear como sólido 3D con un agujero central de 8.2 mm de diá
G+1 Party Hall Structural Shell
G+1 Party Hall – AutoCAD Design Prompt Design a G+1 RCC-framed Party Hall in AutoCAD with detailed Ground Floor Plan, First Floor Plan, and all-side elevations (front, rear, left
Rope Winch Drum
Create a fully parametric CAD model of a rope winch drum for a construction hoist. Requirements: - Output format: STEP (.step or .stp) - Units: millimeters - Solid body only (no