Brackets and mounts
Bionic Prosthetic Forearm and Claws
- Bounding box
- 93.0 × 79.5 × 252.7 mm
- Engine
- 3D Printing B-rep
- Parameters
- 52
- Published
- November 18, 2026
Download
Free to download and use. See the terms.
The prompt
The 3D-printable bionic prosthetic assembly measures $248\text{ mm}$ in total height ($Z = 0$ to $248\text{ mm}$), $92.4\text{ mm}$ in maximum elbow width ($X$), and $79.5\text{ mm}$ in maximum depth ($Y$), consisting of a single static body (forearm, wrist, and palm) and exactly $3$ movable parts (the three fingers, pivoting solely at their bottom base knuckles). The hollow forearm shell ($Z = 0$ to $155\text{ mm}$) features an elliptical cross-section ($R_y = 0.86 R_x$) lofted along a curve $Y_{\text{offset}}(z) = -2.5\sin(\pi z / 155)\text{ mm}$, flaring at the elbow lip to $R_x = 46.2\text{ mm}$ ($Z = 2.5\text{ mm}$) before tapering linearly from $R_x = 45.8\text{ mm}$ ($Z = 5\text{ mm}$) down to $33.3\text{ mm}$ ($Z = 152\text{ mm}$) with a $3.4\text{ mm}$ wall thickness, narrowing to a circular $R = 18.0\text{ mm}$ wire pass-through at $Z = 155\text{ mm}$, and incorporating a $1.6\text{ mm}$-wide panel groove at $Z = 89.2\text{–}90.8\text{ mm}$, two longitudinal side ribs ($R = 1.3\text{–}1.1\text{ mm}$, $Z = 10\text{–}150\text{ mm}$), six $25^\circ$-pitched ventilation louvers per side ($18.0 \times 1.8\text{ mm}$, $7.0\text{ mm}$ pitch, $Z = 26\text{–}61\text{ mm}$), and four internal mounting bosses ($R = 3.8\text{–}3.2\text{ mm}$, $Z = 6\text{–}22\text{ mm}$ at $45^\circ, 135^\circ, 225^\circ, 315^\circ$). Above the forearm sits a rigid stepped wrist collar ($Z = 155\text{–}171\text{ mm}$, circular bore $R = 18.0\text{ mm}$) with outer radius $R = 34.8\text{ mm}$ interrupted by two $1.0\text{ mm}$ recessed grooves ($R = 33.4\text{ mm}$ at $Z = 160.5\text{–}162.2\text{ mm}$ and $R = 33.6\text{ mm}$ at $Z = 166.5\text{–}168.0\text{ mm}$) and a top lip of $R = 35.0\text{ mm}$, seamlessly fused into a $20\text{ mm}$-tall chamfered solid palm hub ($Z = 171\text{–}191\text{ mm}$) tapering from $R = 36.0\text{ mm}$ ($Z = 173\text{ mm}$) to $35.0\text{ mm}$ ($Z = 187\text{ mm}$) and bevelled to $R = 29.0\text{ mm}$ at the top face. Mounted radially at $r = 25.5\text{ mm}, Z = 189.0\text{ mm}$ at angles of $90^\circ$ (thumb), $235^\circ$, and $305^\circ$, the three rigid single-piece claws each pivot exclusively around a tangential cylindrical base knuckle ($17.0\text{ mm}$ wide, $R = 6.2\text{ mm}$, with $19.0\text{ mm}$ pin caps of $R = 2.8\text{ mm}$), extending outward and upward as a rigid proximal segment ($\Delta r = +5.0\text{ mm}, \Delta Z = +34.0\text{ mm}$, $R = 6.4\text{–}5.2\text{ mm}$ with a dorsal spine rib of $R = 2.0\text{–}1.6\text{ mm}$) through a fixed non-moving mid-knuckle ($14.4\text{ mm}$ wide, $R = 5.0\text{ mm}$) into an inward-curving distal phalanx ($\Delta r = -11.5\text{ mm}, \Delta Z = +26.0\text{ mm}$, $R = 5.0\text{–}3.6\text{ mm}$) terminating in a rounded fingertip cap ($R = 3.6\text{–}1.2\text{ mm}$ over $\Delta r = -1.5\text{ mm}, \Delta Z = +2.5\text{ mm}$) lined with five transverse inner grip ribs ($R = 1.1\text{ mm}$, $7.0\text{ mm}$ wide).
Parameters
| Name | Value | Range |
|---|---|---|
| Elbow flare radius | 46.2 mm | 20 – 60 |
| Forearm radius at Z=5 | 45.8 mm | 20 – 60 |
| Forearm radius at top taper | 33.3 mm | 15 – 50 |
| Top taper height | 152 mm | 100 – 170 |
| Shell wall thickness | 3.4 mm | 1.2 – 6 |
| Depth / width ratio | 0.86 mm | 0.5 – 1 |
| Forearm bend offset | 2.5 mm | 0 – 8 |
| Side rib radius | 1.2 mm | 0.6 – 3 |
| Wrist collar outer radius | 34.8 mm | 20 – 50 |
| Wrist bore radius | 18 mm | 5 – 30 |
| Lower wrist groove radius | 33.4 mm | 20 – 50 |
| Upper wrist groove radius | 33.6 mm | 20 – 50 |
| Palm hub base radius | 36 mm | 20 – 50 |
| Palm hub mid radius | 35 mm | 20 – 50 |
| Palm hub top bevel radius | 29 mm | 15 – 50 |
| Internal boss radius | 3.8 mm | 2 – 6 |
| Internal boss height | 16 mm | 6 – 30 |
| Internal boss radial position | 36.5 mm | 20 – 45 |
| Internal boss centre height | 14 mm | 4 – 30 |
| Panel groove start height | 89.2 mm | 20 – 150 |
| Panel groove width | 1.6 mm | 0.6 – 4 |
| Panel groove outer radius | 39.6 mm | 20 – 50 |
| Panel groove inner radius | 37.5 mm | 20 – 50 |
| Vent louver width | 18 mm | 5 – 30 |
| Vent louver height | 1.8 mm | 0.8 – 4 |
| Vent louver pitch | 7 mm | 3 – 15 |
| First louver height | 27 mm | 10 – 80 |
| Claw mount radius | 25.5 mm | 10 – 40 |
| Claw mount height | 189 mm | 150 – 210 |
| Base knuckle width | 17 mm | 8 – 30 |
| Base knuckle radius | 6.2 mm | 3 – 12 |
| Pin cap radius | 2.8 mm | 1.5 – 6 |
| Pin cap length | 19 mm | 10 – 35 |
| Proximal radial change | 5 mm | -5 – 20 |
| Proximal height change | 34 mm | 10 – 60 |
| Proximal base radius | 6.4 mm | 2 – 12 |
| Proximal end radius | 5.2 mm | 2 – 10 |
| Dorsal spine base radius | 2 mm | 0.8 – 4 |
| Dorsal spine end radius | 1.6 mm | 0.8 – 4 |
| Mid knuckle width | 14.4 mm | 6 – 25 |
| Mid knuckle radius | 5 mm | 2 – 10 |
| Distal radial change | -11.5 mm | -25 – 5 |
| Distal height change | 26 mm | 10 – 50 |
| Distal base radius | 5 mm | 2 – 10 |
| Distal end radius | 3.6 mm | 1.5 – 8 |
| Tip radial change | -1.5 mm | -6 – 6 |
| Tip height change | 2.5 mm | 0 – 8 |
| Tip base radius | 3.6 mm | 1.5 – 8 |
| Tip end radius | 1.2 mm | 0.5 – 4 |
| Grip rib radius | 1.1 mm | 0.5 – 3 |
| Grip rib width | 7 mm | 3 – 15 |
| Grip rib inward offset | 3.2 mm | 1 – 8 |
Every value above is a live dimension. Open a model like this in the editor and each one becomes a slider you can drag before exporting.
More models
Browse the full gallery →UAV Ogive Nose Cone
Design a watertight, 3D-printable aerodynamic nose cone module for a fixed-wing tactical UAV, optimized for printing in Carbon Fiber Filled PETG (PETG-CF). The base of the nose con
Trumpet Lyre Mount Main Body
A single 3D mechanical CAD part for a trumpet music lyre mount (Main Body with Paddle). Geometry details: 1. A 18mm-wide semi-cylindrical clamp arc for a 28mm diameter cylinder, w
Flat-Strap Reel Spool
Create a 3D model of a custom flat-strap reel spool for a home plate housing cavity. Geometry: - A reel spool consisting of two parallel circular outer flanges connected by a cent
PET Recycling Kiosk Frame
Design a production-ready welded steel frame for an outdoor PET bottle recycling and animal feeding kiosk. Create ONLY the steel frame. Do not create covers, motors, tanks, electr
JZX100 Gas Cap Holder
can you make a gas cap holder for a jzx100 chaser. i want you to refer to the image and make a cad very close to the picture
Micro RC Airplane Frame
Create a lightweight 3D-printable indoor micro RC airplane frame. The fuselage is a hollow rectangular boom 200 mm long, 3 mm wide, and 3 mm tall, with an open U-shaped electronics
