3D preview of Automatic Car Parking System Prototype
Loading the interactive model…
Interactive 3D model of Automatic Car Parking System Prototype

Brackets and mounts

Automatic Car Parking System Prototype

5 views
Bounding box
600 × 470 × 162 mm
Engine
3D Printing B-rep
Parameters
36
Published
November 15, 2026

Download

Free to download and use. See the terms.

The prompt

Project Title: 3D Mechanical Assembly & Technical Layout of an Automatic Car Parking System Prototype (Lagos State University B.Eng. Final Year Project) Design Specifications & Scale: Scale Factor: 1:24 scaled prototype model. Overall Base Dimensions: Rectangular board layout of 600 mm length × 470 mm width × 6 mm thickness. Layout Configuration: Single entry lane (approx. 150 mm width) leading into 4 parallel parking bays (each bay dimensioned at 100 mm width × 220 mm depth) with clear white boundary lines/engravings. Key Mechanical & Structural Components to Model: 1. Base Plate & Bay Chassis: Flat mounting base with corner fastening holes (Ø4 mm inset 15 mm from edges). Surface demarcation for the 4 parking slots and vehicle entry/exit corridors. 2. Entry Gate & Servo Actuation Mechanism: Vertical sensor/servo mounting post positioned at the entrance lane. Pivoting boom barrier arm (lightweight profile, 140 mm length × 8 mm × 8 mm cross-section) attached to a micro-servo hub (SG90 footprint profile) capable of 0° to 90° angular travel. 3. Sensor Mounting Fixtures: Overhead ultrasonic sensor bracket positioned above the entrance gate lane. Four individual infrared sensor brackets or rear slot mounting clips positioned at the back wall of each parking bay. 4. Microcontroller & Interface Enclosure: Compact housing box on the side of the base plate representing an Arduino Uno board layout and breadboard area. Integrated faceplate cutout for a 16×2 character LCD display module and dual indicator light cutouts (Green/Red LEDs). Output Requirements: Provide clean 2D orthographic projections (Top, Front, Side views) with standard mechanical dimensioning, as well as a fully rendered 3D assembly model showing component integration.

Parameters

NameValueRange
Base length600 mm100 – 1000
Base width470 mm100 – 700
Base thickness6 mm2 – 20
Corner hole diameter4 mm2 – 8
Corner hole inset15 mm5 – 30
Lane marking width2.5 mm1 – 6
Entry lane width150 mm80 – 300
Parking bay width100 mm60 – 200
Parking bay depth220 mm80 – 300
Parking bay count4 mm1 – 8
Gate post footprint30 mm15 – 60
Gate post height90 mm30 – 180
Barrier arm length140 mm60 – 250
Barrier arm width8 mm4 – 20
Barrier arm height8 mm4 – 20
Hinge pin diameter4 mm2 – 8
Hinge pin length32 mm10 – 60
Servo body length22.5 mm10 – 50
Servo body width12.5 mm8 – 30
Servo body height28.5 mm10 – 50
Entrance sensor post footprint16 mm10 – 50
Entrance sensor post height140 mm50 – 250
Bay sensor rail length450 mm200 – 600
Bay sensor rail width20 mm10 – 60
Bay sensor rail thickness8 mm4 – 20
Bay sensor rail height150 mm60 – 300
Bay sensor bracket footprint24 mm12 – 50
Bay sensor bracket height20 mm10 – 50
Enclosure length130 mm60 – 200
Enclosure width90 mm40 – 160
Enclosure height45 mm20 – 100
LCD width72 mm30 – 200
LCD height25 mm12 – 80
LCD thickness3 mm1 – 10
LCD recess depth4 mm1 – 10
LED indicator hole diameter4 mm2 – 8

Every value above is a live dimension. Open a model like this in the editor and each one becomes a slider you can drag before exporting.

Automatic Car Parking System Prototype - Free CAD Model (STEP, STL) | TextoCAD