Brackets and mounts
450 Class Quadcopter Frame
- Bounding box
- 501.1 × 501.1 × 178.5 mm
- Engine
- 3D Printing B-rep
- Parameters
- 44
- Published
- November 18, 2026
Download
Free to download and use. See the terms.
The prompt
Part drawings (top / front / side dimensions) Part Top view (X × Y) Front view (Y × Z) Side view (X × Z) Z position Bottom plate 110 × 110, 12 mm corner chamfers 110 × 2.5 110 × 2.5 0 to 2.5 Arm ×4 210 × 20, R10 outer tip 20 × 4 210 × 4 (along its axis) 2.5 to 6.5 Top plate 110 × 110, same outline 110 × 2.5 110 × 2.5 32.5 to 35 Motor 2212 ×4 Ø28 Ø28 × 26 plus shaft Ø28 × 26 plus shaft 6.5 to 32.5 Prop 10" ×4 Ø254 254 × ~3 254 × ~3 about 34 Battery 130 × 45 45 × 30 130 × 30 −36 to −6 Battery tray 140 × 64, R5 corners 64 × 2.5 140 × 2.5 −38.5 to −36 Camera plate 60 × 40, centered at x = 50 40 × 2.5 60 × 2.5 −56 to −53.5 Landing leg ×4 Ø12 tube Ø12 × 80 Ø12 × 80 −77.5 to 2.5 GPS mast Ø10 at (−30, 0) Ø10 × 70 Ø10 × 70 35 to 105 Flight controller 36 × 36 board 36 × ~8 36 × ~8 on top plate, 5 mm soft-mount standoffs ESC ×4 (30A) ~45 × 24 24 × 8 45 × 8 on arm, r = 105 to 150 The leg, ESC and FC sizes are typical, so check them against your actual parts. Hole and slot coordinates Bottom plate Arm holes for the +X+Y arm: (46.7, 38.2), (38.2, 46.7), (32.5, 24.0), (24.0, 32.5). Mirror these into the other three quadrants to get 16 holes. Top-plate standoffs: (±45, ±10). Tray standoffs: (±50, ±27). PDB holes: (±15.25, ±15.25). Top plate Standoffs: (±45, ±10). FC holes: (±15.25, ±15.25). Mast socket: (−30, ±8). Arm (local x from the inner end, y across the width) Plate bolts: (10, ±6) and (30, ±6). Leg clamp: (45, 0) and (65, 0). Motor center: x = 195, with a Ø10 shaft clearance hole. Motor screws on a Ø16 circle, rotated 45° to the arm: (195 ± 5.66, ±5.66). With a 20 mm wide arm, a 0° pattern would leave under 1 mm of edge material. Tray Standoffs: (±50, ±27). Four strap slots, 14 × 3 mm with the long side along X, at (±30, ±27.5). Use a 12 mm wide strap. Camera-plate holes: (38, ±14) and (62, ±14). Camera plate Same four holes, local (±12, ±14). Standoffs Plate to plate: 4 × M3 × 30 mm. Plate to tray: 4 × M3 × 36 mm. Use countersunk screws on the tray top so the battery sits flat. Tray to camera plate: 4 × M3 × 15 mm. I made the arm 4 mm instead of the 3 mm from the earlier table. A 3 mm flat arm flexes about 6 mm at full thrust, and 4 mm cuts that to about 2.5 mm.
Parameters
| Name | Value | Range |
|---|---|---|
| Frame plate width | 110 mm | 60 – 200 |
| Plate thickness | 2.5 mm | 1.2 – 6 |
| Plate corner chamfer | 12 mm | 0 – 30 |
| Bottom-to-top plate standoff length | 30 mm | 15 – 60 |
| Arm length | 210 mm | 120 – 300 |
| Arm width | 20 mm | 12 – 40 |
| Arm thickness | 4 mm | 3 – 8 |
| Arm tip radius | 10 mm | 5 – 25 |
| Arm inner end radius from centre | 30 mm | 10 – 60 |
| Arm axis angle from X | 45 deg | 0 – 90 |
| Leg/clamp position along arm | 55 mm | 40 – 80 |
| Motor diameter | 28 mm | 15 – 60 |
| Motor height | 26 mm | 10 – 60 |
| Motor shaft diameter | 10 mm | 4 – 16 |
| Motor centre from arm inner end | 195 mm | 80 – 280 |
| Propeller diameter | 254 mm | 100 – 400 |
| Propeller thickness | 3 mm | 1 – 8 |
| Propeller height above bed | 34 mm | 10 – 120 |
| Battery length | 130 mm | 50 – 250 |
| Battery width | 45 mm | 20 – 120 |
| Battery height | 30 mm | 10 – 80 |
| Battery tray length | 140 mm | 60 – 280 |
| Battery tray width | 64 mm | 30 – 160 |
| Battery tray thickness | 2.5 mm | 1.2 – 6 |
| Battery tray corner radius | 5 mm | 1 – 20 |
| Plate-to-tray standoff length | 36 mm | 10 – 80 |
| Landing leg tube diameter | 12 mm | 6 – 25 |
| Landing leg length | 80 mm | 30 – 200 |
| Flight controller board size | 36 mm | 20 – 80 |
| Flight controller height | 8 mm | 3 – 30 |
| FC soft-mount standoff | 5 mm | 1 – 20 |
| ESC length along arm | 45 mm | 20 – 90 |
| ESC width | 24 mm | 10 – 50 |
| ESC height | 8 mm | 3 – 25 |
| ESC centre radius from frame centre | 127 mm | 80 – 180 |
| GPS mast diameter | 10 mm | 4 – 20 |
| GPS mast length | 70 mm | 20 – 200 |
| Camera plate length | 60 mm | 30 – 120 |
| Camera plate width | 40 mm | 20 – 100 |
| Camera plate thickness | 2.5 mm | 1.2 – 6 |
| Camera plate centre offset in X | 50 mm | 0 – 90 |
| Tray-to-camera plate standoff | 15 mm | 5 – 60 |
| M3 clearance hole | 3.4 mm | 2.5 – 5 |
| Standoff outer diameter | 5.5 mm | 3 – 12 |
Every value above is a live dimension. Open a model like this in the editor and each one becomes a slider you can drag before exporting.
More models
Browse the full gallery →UAV Ogive Nose Cone
Design a watertight, 3D-printable aerodynamic nose cone module for a fixed-wing tactical UAV, optimized for printing in Carbon Fiber Filled PETG (PETG-CF). The base of the nose con
Trumpet Lyre Mount Main Body
A single 3D mechanical CAD part for a trumpet music lyre mount (Main Body with Paddle). Geometry details: 1. A 18mm-wide semi-cylindrical clamp arc for a 28mm diameter cylinder, w
Flat-Strap Reel Spool
Create a 3D model of a custom flat-strap reel spool for a home plate housing cavity. Geometry: - A reel spool consisting of two parallel circular outer flanges connected by a cent
PET Recycling Kiosk Frame
Design a production-ready welded steel frame for an outdoor PET bottle recycling and animal feeding kiosk. Create ONLY the steel frame. Do not create covers, motors, tanks, electr
JZX100 Gas Cap Holder
can you make a gas cap holder for a jzx100 chaser. i want you to refer to the image and make a cad very close to the picture
Micro RC Airplane Frame
Create a lightweight 3D-printable indoor micro RC airplane frame. The fuselage is a hollow rectangular boom 200 mm long, 3 mm wide, and 3 mm tall, with an open U-shaped electronics
