Brackets and mounts
XROS 5-Cartridge Storage Case
- Bounding box
- 186.3 × 33.6 × 42.0 mm
- Engine
- Precision B-rep
- Parameters
- 40
- Published
- November 21, 2026
Download
Free to download and use. See the terms.
The prompt
Design a complete 3D-printable storage case from scratch for 5 Vaporesso XROS cartridges. Main body: * Compact rectangular design with 5 individual cartridge slots. * Flat bottom, durable walls, slightly chamfered outer edges. * Optimize dimensions for minimum overall size. * Arrange slots efficiently while maintaining enough material between them. Cartridge dimensions: * Base: 22.28 mm long × 11.62 mm wide × 11 mm high. * Base corner radius: 3–4 mm. * Tank: 23 mm long × 13 mm wide. * Total cartridge height, including mouthpiece: approximately 37.6 mm. * Slots must accommodate only the bottom 11 mm section, leaving the tank and mouthpiece exposed for easy removal. Removable lid: * Design a separate, full-height removable lid that covers the entire cartridge. * Use a mechanical snap-fit latch on one side and a guiding alignment groove on the opposite side. * Ensure secure attachment, easy removal and no unwanted movement. * The latch should produce a satisfying click without requiring excessive force. * Add ergonomic grip grooves and textured finger-contact surfaces to the lid. FDM printing requirements (PLA): * Account for approximately 0.3 mm dimensional narrowing in printed grooves. * Include appropriate clearances for moving and mating parts. * Avoid overly tight tolerances, fragile clips and thin walls. * Optimize geometry for strength and minimal support requirements. Final requirements: Create a functional, compact, accurately dimensioned 3D model consisting of two separate printable parts: the lower body and removable lid. Prioritize practical usability, reliable snap-fit engagement, smooth assembly, easy opening and long-term durability. Ensure all parts are geometrically compatible and ready for FDM printing.
Parameters
| Name | Value | Range |
|---|---|---|
| Layout gap (part spacing) | 110 mm | 80 – 300 |
| Body length (X) | 74 mm | 60 – 90 |
| Body width (Y) | 29 mm | 20 – 40 |
| Body height (Z) | 13 mm | 8 – 20 |
| Pocket length (X) | 12 mm | 10 – 14 |
| Pocket width (Y) | 22.7 mm | 18 – 28 |
| Pocket depth (floor = height - depth) | 11 mm | 8 – 14 |
| Pocket corner radius | 3.7 mm | 1 – 5 |
| Pocket pitch (X) | 14 mm | 12 – 18 |
| Top/bottom outer edge chamfer | 1 mm | 0.2 – 2 |
| Snap ridge height | 0.8 mm | 0.4 – 1.5 |
| Snap ridge width (X) | 10 mm | 4 – 20 |
| Snap ridge centre height (Z) | 7 mm | 3 – 10 |
| Guide rib height | 1 mm | 0.5 – 2 |
| Guide rib width (Z) | 1.5 mm | 1 – 3 |
| Guide rib centre height (Z) | 5 mm | 3 – 8 |
| Lid outer length (X) | 78.6 mm | 70 – 100 |
| Lid outer width (Y) | 33.6 mm | 28 – 45 |
| Lid outer height (Z) | 42 mm | 30 – 60 |
| Lid side wall thickness | 2 mm | 1.2 – 3 |
| Lid top plate thickness | 2 mm | 1.2 – 3 |
| Latch arm width (X) | 10 mm | 5 – 15 |
| Latch arm thickness | 1.2 mm | 0.8 – 2 |
| Latch arm length | 12 mm | 6 – 20 |
| Latch hook depth | 0.8 mm | 0.4 – 1.5 |
| Latch arm root height | 2 mm | 0 – 10 |
| Alignment groove width (nominal) | 2.2 mm | 1.5 – 4 |
| Alignment groove depth | 1.3 mm | 0.8 – 2.5 |
| PLA narrowing compensation | 0.3 mm | 0 – 0.5 |
| Grip groove count | 5 mm | 3 – 8 |
| Grip groove depth | 0.8 mm | 0.3 – 1.5 |
| Grip groove pitch | 1.2 mm | 0.8 – 3 |
| Grip groove width (Z) | 0.6 mm | 0.3 – 1.5 |
| Grip groove length (X) | 50 mm | 20 – 70 |
| Lowest grip groove height | 20 mm | 5 – 35 |
| Knurl pad width (X) | 40 mm | 20 – 60 |
| Knurl pad height (Y) | 20 mm | 10 – 30 |
| Knurl depth | 0.5 mm | 0.2 – 1 |
| Knurl line pitch | 2 mm | 1 – 4 |
| Knurl line width | 0.6 mm | 0.3 – 1.2 |
Every value above is a live dimension. Open a model like this in the editor and each one becomes a slider you can drag before exporting.
More models
Browse the full gallery →UAV Ogive Nose Cone
Design a watertight, 3D-printable aerodynamic nose cone module for a fixed-wing tactical UAV, optimized for printing in Carbon Fiber Filled PETG (PETG-CF). The base of the nose con
Trumpet Lyre Mount Main Body
A single 3D mechanical CAD part for a trumpet music lyre mount (Main Body with Paddle). Geometry details: 1. A 18mm-wide semi-cylindrical clamp arc for a 28mm diameter cylinder, w
Flat-Strap Reel Spool
Create a 3D model of a custom flat-strap reel spool for a home plate housing cavity. Geometry: - A reel spool consisting of two parallel circular outer flanges connected by a cent
PET Recycling Kiosk Frame
Design a production-ready welded steel frame for an outdoor PET bottle recycling and animal feeding kiosk. Create ONLY the steel frame. Do not create covers, motors, tanks, electr
Hydraulic Wing and Flaperon Demonstrator
Create a parametric 3D CAD model of a hydraulic aircraft wing and movable flaperon based on the reference sketch. **Wing dimensions:** - 240 mm chord, 120 mm span, 48 mm thickness
JZX100 Gas Cap Holder
can you make a gas cap holder for a jzx100 chaser. i want you to refer to the image and make a cad very close to the picture
