Gears and transmission
Wash Drone Quadcopter Frame
- Bounding box
- 416.9 × 416.9 × 225.1 mm
- Engine
- Precision B-rep
- Parameters
- 42
- Published
- November 2, 2026
Download
Free to download and use. See the terms.
The prompt
Design a quadcopter drone frame for facade inspection and cleaning, called "Wash Drone." Main frame: Central hub, a flat hexagonal plate, 160 mm across flats, 4 mm thick, carbon-fiber composite. Four arms extend from the hub in an X configuration, each arm 275 mm long from hub center to motor mount, 20 mm wide, and 10 mm thick, tapering slightly toward the motor end. Motor mounts: At the end of each arm, a circular motor mount plate, 28 mm in diameter, with 4 mounting holes (M3, arranged in a 19 mm bolt circle) for 2212-size brushless motors. Central body/payload bay: Below the hub, a rectangular enclosure, 120mm x 100mm x 60mm, with a removable bottom hatch for battery access. Mount points inside for a Pixhawk 6C flight controller (36mm x 50mm board) and a Raspberry Pi 5 (85mm x 56mm board), stacked vertically with 15mm clearance between boards. Camera gimbal mount: Front-facing 2-axis gimbal cradle, 40mm diameter circular mount, positioned at the front-bottom of the central body, angled 15 degrees downward from horizontal. Cleaning module: Rear-mounted housing, 90mm x 40mm x 30mm, containing a fluid reservoir (cylindrical, 60mm diameter x 80mm height) and two spray nozzle outlets (8mm diameter) angled 30 degrees downward, spaced 50mm apart. Landing gear: six fixed skid legs, each a 10 mm diameter carbon rod, bent at a 90-degree angle, providing 80 mm ground clearance, mounted at the base of each arm. Battery bay: Slide-in tray for a 6S LiPo battery, 145mm x 51mm x 45mm envelope, secured with a Velcro strap channel. Overall motor-to-motor diagonal span: 550mm. The total design should be lightweight, optimized for a 3.5-4 kg MTOW, with mounting holes and clearances suitable for 3D printing in PETG or carbon-nylon composite.
Parameters
| Name | Value | Range |
|---|---|---|
| Hex Plate Across Flats | 160 mm | 100 – 300 |
| Hub Plate Thickness | 4 mm | 2 – 10 |
| Arm Length (center to motor mount) | 275 mm | 200 – 400 |
| Arm Width at Hub | 20 mm | 10 – 30 |
| Arm Width at Tip | 16 mm | 8 – 25 |
| Arm Thickness | 10 mm | 5 – 20 |
| Motor Mount Diameter | 28 mm | 20 – 40 |
| Motor Mount Thickness | 3 mm | 2 – 6 |
| Bolt Circle Diameter | 19 mm | 12 – 25 |
| Mounting Hole Diameter | 3.2 mm | 2 – 5 |
| Number of Holes | 4 | 3 – 6 |
| Enclosure Length (X) | 120 mm | 80 – 200 |
| Enclosure Width (Y) | 100 mm | 60 – 200 |
| Enclosure Height (Z) | 60 mm | 40 – 100 |
| Camera Mount Diameter | 40 mm | 20 – 60 |
| Camera Mount Thickness | 10 mm | 5 – 20 |
| Camera Tilt Angle (°) | 15 ° | 0 – 30 |
| Camera Bracket Length | 5 mm | 2 – 10 |
| Housing Length (X) | 90 mm | 50 – 150 |
| Housing Width (Y) | 40 mm | 20 – 80 |
| Housing Height (Z) | 30 mm | 10 – 50 |
| Nozzle Diameter | 8 mm | 4 – 12 |
| Nozzle Spacing | 50 mm | 20 – 80 |
| Nozzle Angle Down (°) | 30 ° | 0 – 45 |
| Tank Diameter | 60 mm | 40 – 80 |
| Tank Height | 80 mm | 50 – 120 |
| Leg Diameter | 10 mm | 5 – 20 |
| Vertical Leg Length | 144 mm | 100 – 200 |
| Horizontal Foot Length | 30 mm | 10 – 50 |
| Bend Radius | 10 mm | 5 – 15 |
| Inner Leg Radial Position | 60 mm | 40 – 100 |
| Mid Leg Radial Position | 140 mm | 100 – 200 |
| Battery Tray Length | 145 mm | 100 – 200 |
| Battery Tray Width | 51 mm | 30 – 70 |
| Battery Tray Height | 45 mm | 30 – 60 |
| Pixhawk Length | 36 mm | 30 – 50 |
| Pixhawk Width | 50 mm | 30 – 60 |
| Pixhawk Thickness | 5 mm | 2 – 10 |
| Raspberry Pi Length | 85 mm | 60 – 100 |
| Raspberry Pi Width | 56 mm | 40 – 60 |
| Raspberry Pi Thickness | 5 mm | 2 – 10 |
| Bottom Hatch Thickness | 2 mm | 1 – 5 |
Every value above is a live dimension. Open a model like this in the editor and each one becomes a slider you can drag before exporting.
More models
Browse the full gallery →Spur Gearbox
design gearbox
Involute Spur Gear with Keyway
Precision Involute Spur Gear with Hub and Keyway: Module (m) of 2.0 mm, 40 teeth (z), Pitch Circle Diameter (d) of 80.00 mm, 20° pressure angle (\alpha), 15.00 mm face width (b), a
Parametric Helical Gear
Create a parametric helical gear with the following specifications: 32 teeth, normal module of 3 mm, right-hand helix, total face width of 80 mm, and a central bore hole with a dia
Rod with Spur Gear
Metal rod diameter is 20 mm and length is 100 mm and right side attach a gear and their OD is 50 mm
Spur Gear (12 Teeth)
Built a gear with 12 teeth
Two-Stage Spur Gear Reduction Assembly
Design a 2-stage spur gear reduction set for 3D printing with an overall 10:1 ratio. Stage 1: A 12-tooth pinion driving a 36-tooth gear (3:1). Stage 2: A 12-tooth pinion coupled