3D preview of Wall-mount ESP32-C5 perfboard enclosure
Loading the interactive model…
Interactive 3D model of Wall-mount ESP32-C5 perfboard enclosure

Brackets and mounts

Wall-mount ESP32-C5 perfboard enclosure

1 views
Bounding box
95.8 × 95.8 × 36 mm
Engine
3D Printing B-rep
Parameters
33
Published
November 22, 2026

Download

Free to download and use. See the terms.

The prompt

I have a esp32 c5 devleopment board soldered to a 80x80mm perf board with two mounting holes on the left side on the top and bottom each 3mm of diamater being 3.5 mm of the side, and 2.5mm off of the top and bottom. I want 3 parts: 1. the bottom housing where I can mount the perferated board using the two mounting holes on the left side. this bottom portion will end up facing out from the wall and need to have a spot to mount the wifi attena. This attena is a flat tappable type attenta which can go on the inside of the print. the outer facing bottom side also need a cutout hole for a status LED. I also need holes on the side of this encolsure to insert heat set copper treads to attach the top and bottom portions. I also need a cut out for the usbc power cable to the esp32 2. top encsolure that will go over the bottom part and use screws that will go thorugh holes in the top part and thread into the heatsets of the bottom part. this top encose will be inwards facitg towards the wall. I also need a cutout for the esp32 type c power cable that matches the cutout in the bottom layer. This inner facing part will use a dovetail sliding join into the third part. 3. this third part will connecet the second part using the dovetail sliding rail and is semipernatnly attaches to the wall.

Parameters

NameValueRange
Perfboard size80 mm60 – 120
Perfboard thickness1.6 mm0.8 – 3
Mounting hole inset from left edge3.5 mm2 – 10
Mounting hole inset from top/bottom edge2.5 mm1.5 – 10
Standoff outer diameter5 mm3 – 8
Standoff height4 mm2 – 10
Standoff hole diameter3 mm2 – 4
Housing inside width86 mm60 – 150
Wall thickness2.5 mm1.2 – 6
Floor thickness2.5 mm1.2 – 6
Housing depth22 mm14 – 40
USB-C cutout width9 mm5 – 14
USB-C cutout height3.5 mm2.5 – 6
Status LED hole diameter5 mm3 – 8
Antenna recess length40 mm20 – 60
Antenna recess width12 mm6 – 20
Heat-set insert hole diameter4.2 mm3 – 6
Heat-set insert depth5 mm3 – 8
Heat-set height below rim5 mm2 – 10
Insert and screw spacing from centre25 mm10 – 35
Top enclosure depth14 mm8 – 30
Press-fit interference per side0.1 mm0 – 0.5
Screw clearance hole diameter3.4 mm2.5 – 4.5
Dovetail rail neck width12 mm8 – 20
Dovetail rail height6 mm4 – 10
Dovetail rail length76 mm40 – 90
Bracket size95 mm70 – 150
Bracket plate thickness4 mm3 – 8
Wall screw hole diameter4.5 mm3.5 – 6
Wall hole inset from edge10 mm6 – 15
Channel rib width40 mm30 – 60
Dovetail sliding clearance0.2 mm0 – 0.5
Set-screw hole diameter3.2 mm2.5 – 5

Every value above is a live dimension. Open a model like this in the editor and each one becomes a slider you can drag before exporting.

Wall-mount ESP32-C5 perfboard enclosure - Free CAD Model (STEP, STL) | TextoCAD