Brackets and mounts
Square Hollow Mounting Block with Side Plate
- Bounding box
- 46.5 × 100 × 100 mm
- Engine
- 3D Printing B-rep
- Parameters
- 9
- Published
- November 22, 2026
Download
Free to download and use. See the terms.
The prompt
Create a square hollow mounting block with a 100x100 mm mounting plate attached to one side, 100 mm total height. 1. Main hollow tower: Create a vertical square prism measuring 42.5 mm by 42.5 mm on the outside and 100 mm in height, centered on the XY plane. Cut a centered square through-hole from top to bottom measuring 31 mm by 31 mm, leaving a uniform wall thickness of 5.75 mm. 2. Side set-screw hole: On the front vertical face (Y-minus face), drill a centered circular through-hole of 6 mm diameter halfway up the height (at Z = 50 mm), passing only through the front wall into the inner cavity. 3. Side mounting plate: Attached flush to the right vertical face (X-plus face) of the tower, create a flat square mounting plate measuring 100 mm by 100 mm and 4 mm in thickness, centered vertically at Z = 50 mm and centered along the Y-axis, so its outer face sits at X = 25.25 mm. 4. Mounting plate holes: Drill four 5 mm diameter through-holes near the corners of the 100x100 mm mounting plate, positioned 12 mm inward from each outer edge (at Y = ±38 mm and Z = 12 mm / 88 mm), passing completely through the 4 mm plate. Add 2 mm fillets to the four outer corners of the mounting plate.
Parameters
| Name | Value | Range |
|---|---|---|
| Tower outer width | 42.5 mm | 20 – 80 |
| Tower height | 100 mm | 40 – 200 |
| Tower wall thickness | 5.75 mm | 1.2 – 10 |
| Set-screw hole diameter | 6 mm | 2 – 12 |
| Plate edge length | 100 mm | 40 – 200 |
| Plate thickness | 4 mm | 1.2 – 10 |
| Outer corner fillet radius | 2 mm | 0.5 – 8 |
| Mounting hole diameter | 5 mm | 2 – 10 |
| Hole inset from plate edges | 12 mm | 3 – 40 |
Every value above is a live dimension. Open a model like this in the editor and each one becomes a slider you can drag before exporting.
More models
Browse the full gallery →UAV Ogive Nose Cone
Design a watertight, 3D-printable aerodynamic nose cone module for a fixed-wing tactical UAV, optimized for printing in Carbon Fiber Filled PETG (PETG-CF). The base of the nose con
Trumpet Lyre Mount Main Body
A single 3D mechanical CAD part for a trumpet music lyre mount (Main Body with Paddle). Geometry details: 1. A 18mm-wide semi-cylindrical clamp arc for a 28mm diameter cylinder, w
Flat-Strap Reel Spool
Create a 3D model of a custom flat-strap reel spool for a home plate housing cavity. Geometry: - A reel spool consisting of two parallel circular outer flanges connected by a cent
PET Recycling Kiosk Frame
Design a production-ready welded steel frame for an outdoor PET bottle recycling and animal feeding kiosk. Create ONLY the steel frame. Do not create covers, motors, tanks, electr
Hydraulic Wing and Flaperon Demonstrator
Create a parametric 3D CAD model of a hydraulic aircraft wing and movable flaperon based on the reference sketch. **Wing dimensions:** - 240 mm chord, 120 mm span, 48 mm thickness
JZX100 Gas Cap Holder
can you make a gas cap holder for a jzx100 chaser. i want you to refer to the image and make a cad very close to the picture
