Brackets and mounts
Smart Pet Feeder Assembly
- Bounding box
- 260.0 × 220.0 × 10.0 mm
- Engine
- Precision B-rep
- Parameters
- 57
- Published
- October 24, 2026
Download
Free to download and use. See the terms.
The prompt
Create a multi-part assembly of a smart pet feeder, in millimeters. Origin is the center of the bottom of the base plate, Z up, front is +Y. Keep each part as a separate body, not merged. Parts: 1. Base plate: 260 x 220 x 10, rounded corners R10, with four rubber feet (dia 15 x 5) underneath. 2. Column: 40 x 40 square tube, 480 tall, standing on the base plate at X=0, Y=-90, fixed with two L-brackets. 3. Load cell: bar 80 x 12.7 x 12.7 lying along X, mounted on a 20 x 20 x 10 spacer on the base plate at X=0, Y=15, with a second spacer on its free end. 4. Weighing platform: disc dia 170 x 5 on the free-end spacer, floating at least 3 mm above the base plate. 5. Pet bowl: hollow, top dia 150, base dia 100, height 50, centered on the platform. 6. Food container: clear cylinder dia 130 x 170 tall, wall 2, funnel bottom narrowing to a 40 mm outlet, with a lid. It sits in a ring holder on an arm from the column at Z=350, centered at X=0, Y=15. 7. Chute: vertical tube 40 ID / 46 OD from the container outlet down to about 40 mm above the bowl rim. 8. Gate: 3 mm plate (50 x 50) across the outlet, driven by an SG90 servo (23 x 12.2 x 29) on a small bracket. 9. Camera arm: 15 x 15 bar from the column at Z=200, running forward at X=45. At its end is a 35 x 45 x 20 hollow camera housing with a 12 mm lens hole, tilted 60 degrees down toward the bowl. 10. Electronics box: hollow 80 x 100 x 60, wall 3, with a removable lid, mounted left of the column at Z=270 to 330 with a bridge bracket. It has a 10 x 5 power port hole and 4 vent slots. Fillet exterior edges 2 mm. Colors: transparent container, silver bowl, black servo and load cell, white or gray frame and box.
Parameters
| Name | Value | Range |
|---|---|---|
| Base Length | 260 mm | 150 – 400 |
| Base Width | 220 mm | 120 – 350 |
| Base Thickness | 10 mm | 4 – 30 |
| Base Corner Radius | 10 mm | 2 – 30 |
| Foot Diameter | 15 mm | 5 – 30 |
| Foot Height | 5 mm | 2 – 15 |
| Foot Inset | 20 mm | 5 – 60 |
| Edge Fillet | 2 mm | 0.5 – 5 |
| Column Size | 40 mm | 20 – 80 |
| Column Height | 480 mm | 200 – 800 |
| Column Wall | 2 mm | 1 – 10 |
| Column Y Position | -90 mm | -150 – -20 |
| Spacer Size | 20 mm | 10 – 40 |
| Spacer Height | 10 mm | 4 – 30 |
| Load Cell Length | 80 mm | 40 – 150 |
| Load Cell Width | 12.7 mm | 5 – 30 |
| Load Cell Height | 12.7 mm | 5 – 30 |
| Platform Diameter | 170 mm | 80 – 300 |
| Platform Thickness | 5 mm | 2 – 20 |
| Bowl Top Diameter | 150 mm | 80 – 300 |
| Bowl Base Diameter | 100 mm | 50 – 200 |
| Bowl Height | 50 mm | 20 – 150 |
| Bowl Wall | 2 mm | 1 – 10 |
| Container Diameter | 130 mm | 60 – 250 |
| Container Height | 170 mm | 80 – 400 |
| Container Wall | 2 mm | 1 – 10 |
| Funnel Outlet Diameter | 40 mm | 15 – 100 |
| Funnel Height | 20 mm | 5 – 60 |
| Lid Thickness | 5 mm | 2 – 15 |
| Ring Outer Diameter | 140 mm | 80 – 250 |
| Ring Inner Diameter | 132 mm | 70 – 240 |
| Ring Thickness | 5 mm | 2 – 20 |
| Arm Length | 110 mm | 40 – 250 |
| Arm Width | 15 mm | 5 – 40 |
| Arm Height | 15 mm | 5 – 40 |
| Chute ID | 40 mm | 15 – 100 |
| Chute OD | 46 mm | 20 – 120 |
| Chute Length | 210 mm | 50 – 400 |
| Gate Size | 50 mm | 20 – 100 |
| Gate Thickness | 3 mm | 1 – 10 |
| Servo X | 23 mm | 10 – 50 |
| Servo Y | 12.2 mm | 5 – 30 |
| Servo Z | 29 mm | 10 – 60 |
| Camera Arm Size | 15 mm | 5 – 40 |
| Camera Arm Z | 200 mm | 100 – 350 |
| Camera Housing X | 35 mm | 15 – 80 |
| Camera Housing Y | 45 mm | 20 – 100 |
| Camera Housing Z | 20 mm | 10 – 60 |
| Camera Lens Dia | 12 mm | 4 – 30 |
| Camera Tilt | 60 deg | 0 – 90 |
| Electronics Box X | 80 mm | 40 – 200 |
| Electronics Box Y | 100 mm | 40 – 250 |
| Electronics Box Z | 60 mm | 20 – 150 |
| Electronics Wall | 3 mm | 1 – 10 |
| Power Port Width | 10 mm | 3 – 30 |
| Power Port Height | 5 mm | 2 – 20 |
| Vent Slot Count | 4 count | 1 – 10 |
Every value above is a live dimension. Open a model like this in the editor and each one becomes a slider you can drag before exporting.
More models
Browse the full gallery →Trumpet Lyre Mount Main Body
A single 3D mechanical CAD part for a trumpet music lyre mount (Main Body with Paddle). Geometry details: 1. A 18mm-wide semi-cylindrical clamp arc for a 28mm diameter cylinder, w
UAV Ogive Nose Cone
Design a watertight, 3D-printable aerodynamic nose cone module for a fixed-wing tactical UAV, optimized for printing in Carbon Fiber Filled PETG (PETG-CF). The base of the nose con
Flat-Strap Reel Spool
Create a 3D model of a custom flat-strap reel spool for a home plate housing cavity. Geometry: - A reel spool consisting of two parallel circular outer flanges connected by a cent
PET Recycling Kiosk Frame
Design a production-ready welded steel frame for an outdoor PET bottle recycling and animal feeding kiosk. Create ONLY the steel frame. Do not create covers, motors, tanks, electr
Kugoo G2 Pro Rear Swingarm for KuKirin G4
Create a detailed 1:1 CAD drawing of custom rear swingarms for the Kugoo G2 Pro 2020 electric scooter. The swingarms must be designed to fit a KuKirin G4 hub motor instead of the o
Humanoid Robot Exploded Assembly
Design a 3D CAD model of a fully autonomous humanoid biped robot for the Robofest AI HOMO BOT competition. Dimensions Height: 800 mm (80 cm) Maximum weight: 20 kg Lightweight modu