Gears and transmission
Slider-Bed Belt Conveyor 6096 mm
- Bounding box
- 6116.0 × 2061.0 × 1016.1 mm
- Engine
- Precision B-rep
- Parameters
- 31
- Published
- October 6, 2026
Download
Free to download and use. See the terms.
The prompt
Create a clean, conventional horizontal slider-bed belt conveyor assembly for factory material handling. Dimensions: overall conveyor length 6096 mm (20 ft); usable flat belt width 1524 mm (60 in); top-of-belt elevation 1016 mm (40 in). Make the belt a clearly visible continuous dark rubber loop running horizontally around one drive pulley and one tail pulley, with a flat upper carrying surface and lower return run. Use two slim parallel galvanized steel C-channel side frames, each about 200 mm deep, located along both belt edges. Put a compact gearmotor under the drive end on the left side, coupled to the drive pulley by a shaft and guard. Include exactly four evenly spaced adjustable steel H-stand support frames: vertical legs, cross-brace, and small leveling feet. Include cross members beneath the bed. Do not include any vertical panels, free-floating rods, ladders, guards, or loose unrelated parts. The assembly should look like a real straight belt conveyor viewed in a three-quarter isometric orientation.
Parameters
| Name | Value | Range |
|---|---|---|
| Overall Length | 6096 mm | 1000 – 20000 |
| Usable Belt Width | 1524 mm | 300 – 3000 |
| Top-of-Belt Elevation | 1016 mm | 300 – 2500 |
| Belt Thickness | 12 mm | 4 – 40 |
| Belt-to-Frame Gap | 4 mm | 0 – 50 |
| Pulley Diameter | 250 mm | 80 – 800 |
| Pulley Centre Inset | 250 mm | 150 – 1500 |
| Pulley Shaft Diameter | 60 mm | 20 – 150 |
| Shaft Overhang Past Frame | 100 mm | 0 – 400 |
| Frame Channel Width | 80 mm | 30 – 250 |
| Frame Channel Depth | 200 mm | 50 – 600 |
| Channel Wall Thickness | 20 mm | 5 – 60 |
| Stand Height to Frame | 800 mm | 200 – 2000 |
| Leg Section | 60 mm | 20 – 200 |
| Number of Stands | 4 pcs | 2 – 8 |
| First Stand Offset | 762 mm | 100 – 3000 |
| Stand Pitch | 1524 mm | 200 – 5000 |
| Number of Cross Members | 3 pcs | 1 – 10 |
| First Cross Member Offset | 1524 mm | 100 – 5000 |
| Cross Member Pitch | 1524 mm | 200 – 5000 |
| Cross Member Width | 80 mm | 20 – 250 |
| Cross Member Depth | 170 mm | 50 – 400 |
| Gearmotor Length | 500 mm | 100 – 1200 |
| Gearmotor Width | 350 mm | 100 – 900 |
| Gearmotor Height | 350 mm | 100 – 900 |
| Drive Shaft Length | 400 mm | 50 – 1500 |
| Drive Shaft Diameter | 50 mm | 10 – 200 |
| Coupling Guard Length | 250 mm | 50 – 800 |
| Coupling Guard Width | 180 mm | 50 – 600 |
| Coupling Guard Height | 180 mm | 50 – 600 |
| Drive Shaft Offset From Frame | 74 mm | 10 – 600 |
Every value above is a live dimension. Open a model like this in the editor and each one becomes a slider you can drag before exporting.
More models
Browse the full gallery →Spur Gearbox
design gearbox
Involute Spur Gear with Keyway
Precision Involute Spur Gear with Hub and Keyway: Module (m) of 2.0 mm, 40 teeth (z), Pitch Circle Diameter (d) of 80.00 mm, 20° pressure angle (\alpha), 15.00 mm face width (b), a
Parametric Helical Gear
Create a parametric helical gear with the following specifications: 32 teeth, normal module of 3 mm, right-hand helix, total face width of 80 mm, and a central bore hole with a dia
Rod with Spur Gear
Metal rod diameter is 20 mm and length is 100 mm and right side attach a gear and their OD is 50 mm
Spur Gear (12 Teeth)
Built a gear with 12 teeth
Two-Stage Spur Gear Reduction Assembly
Design a 2-stage spur gear reduction set for 3D printing with an overall 10:1 ratio. Stage 1: A 12-tooth pinion driving a 36-tooth gear (3:1). Stage 2: A 12-tooth pinion coupled