Brackets and mounts
Six-Wheel Rocker-Bogie Rover Exploded Assembly
- Bounding box
- 6210.0 × 350.0 × 487.5 mm
- Engine
- Precision B-rep
- Parameters
- 49
- Published
- October 23, 2026
Download
Free to download and use. See the terms.
The prompt
Create a detailed, editable, dimensionally accurate 3D CAD assembly of an 850 mm long, six-wheel Rocker-Bogie rover for a school robotics project. Main chassis 600 × 350 mm; overall length 850 mm; target width 480–520 mm; six wheels approximately 95 mm diameter. Create separate left and right rocker-bogie linkages with pivot pins, bearings or bushings, brackets and travel stops. Four powered wheels (front and rear on both sides), two free-rolling middle wheels, adjustable motor mounts. Use PVC, acrylic, metal reinforcement brackets, shafts and standard fasteners. Include low battery tray, removable ESP32/electronics enclosure, adjustable IP camera mast, cable routing and removable front sensor bar. Use millimetres and editable parameters. Check articulation, collisions, ground clearance, fastener access and overall dimensions. Deliver editable CAD assembly, dimensioned orthographic drawings, exploded view, bill of materials, cutting plan and STEP export if supported; OBJ/GLB for Blender if available. Do not invent unknown hardware dimensions; use placeholders. Prioritise manufacturability. This is a school prototype for safe simulated targets, not a validated landmine detector. If necessary, create the chassis and suspension first, then add remaining components.
Parameters
| Name | Value | Range |
|---|---|---|
| Exploded layout gap | 650 mm | 300 – 1500 |
| Chassis length | 600 mm | 300 – 900 |
| Chassis width | 350 mm | 200 – 500 |
| Base plate thickness | 6 mm | 3 – 12 |
| Side rail width | 25 mm | 10 – 50 |
| Side rail height | 40 mm | 15 – 80 |
| Mounting hole diameter | 4 mm | 2 – 8 |
| Cable pass-through diameter | 12 mm | 5 – 30 |
| Rocker linkage span | 320 mm | 200 – 450 |
| Linkage bar width | 18 mm | 8 – 40 |
| Linkage bar thickness | 6 mm | 3 – 15 |
| Pivot pin diameter | 10 mm | 4 – 20 |
| Bushing outer diameter | 16 mm | 8 – 30 |
| Travel stop length | 25 mm | 10 – 50 |
| Wheel diameter | 95 mm | 60 – 150 |
| Wheel width | 35 mm | 15 – 60 |
| Wheel bore | 8 mm | 3 – 20 |
| Wheel hub diameter | 30 mm | 15 – 60 |
| Motor mount length | 90 mm | 50 – 150 |
| Motor mount width | 60 mm | 30 – 100 |
| Motor mount thickness | 5 mm | 2 – 12 |
| Adjustment slot length | 40 mm | 10 – 80 |
| Motor shaft hole diameter | 6 mm | 3 – 15 |
| Battery tray length | 250 mm | 150 – 350 |
| Battery tray width | 180 mm | 100 – 300 |
| Battery tray height | 25 mm | 15 – 60 |
| Battery tray wall | 4 mm | 2 – 10 |
| Enclosure length | 180 mm | 100 – 300 |
| Enclosure width | 120 mm | 80 – 200 |
| Enclosure height | 60 mm | 30 – 120 |
| Enclosure wall | 3 mm | 1.5 – 8 |
| Enclosure lid thickness | 4 mm | 2 – 10 |
| Mast base diameter | 40 mm | 20 – 80 |
| Mast height | 400 mm | 300 – 500 |
| Mast tube diameter | 16 mm | 8 – 30 |
| Camera tilt angle | 15 deg | -30 – 45 |
| Camera plate width | 60 mm | 30 – 100 |
| Camera plate height | 40 mm | 20 – 80 |
| Camera mounting hole diameter | 4 mm | 2 – 8 |
| Sensor bar length | 400 mm | 250 – 550 |
| Sensor bar width | 40 mm | 20 – 80 |
| Sensor bar height | 30 mm | 15 – 60 |
| Sensor mounting hole diameter | 5 mm | 2 – 10 |
| M3 placeholder diameter | 3 mm | 2 – 5 |
| M4 placeholder diameter | 4 mm | 3 – 6 |
| M5 placeholder diameter | 5 mm | 4 – 8 |
| Bearing outer diameter | 16 mm | 8 – 30 |
| Bearing inner diameter | 10 mm | 4 – 20 |
| Cable clip diameter | 10 mm | 5 – 20 |
Every value above is a live dimension. Open a model like this in the editor and each one becomes a slider you can drag before exporting.
More models
Browse the full gallery →Trumpet Lyre Mount Main Body
A single 3D mechanical CAD part for a trumpet music lyre mount (Main Body with Paddle). Geometry details: 1. A 18mm-wide semi-cylindrical clamp arc for a 28mm diameter cylinder, w
UAV Ogive Nose Cone
Design a watertight, 3D-printable aerodynamic nose cone module for a fixed-wing tactical UAV, optimized for printing in Carbon Fiber Filled PETG (PETG-CF). The base of the nose con
Flat-Strap Reel Spool
Create a 3D model of a custom flat-strap reel spool for a home plate housing cavity. Geometry: - A reel spool consisting of two parallel circular outer flanges connected by a cent
PET Recycling Kiosk Frame
Design a production-ready welded steel frame for an outdoor PET bottle recycling and animal feeding kiosk. Create ONLY the steel frame. Do not create covers, motors, tanks, electr
Kugoo G2 Pro Rear Swingarm for KuKirin G4
Create a detailed 1:1 CAD drawing of custom rear swingarms for the Kugoo G2 Pro 2020 electric scooter. The swingarms must be designed to fit a KuKirin G4 hub motor instead of the o
Humanoid Robot Exploded Assembly
Design a 3D CAD model of a fully autonomous humanoid biped robot for the Robofest AI HOMO BOT competition. Dimensions Height: 800 mm (80 cm) Maximum weight: 20 kg Lightweight modu