Brackets and mounts
Scaled-Down Mobile X-ray Machine Assembly
- Bounding box
- 305.0 × 475.5 × 770.0 mm
- Engine
- Precision B-rep
- Parameters
- 50
- Published
- October 25, 2026
Download
Free to download and use. See the terms.
The prompt
**scaled-down mobile X-ray machine prototype** dimensions  - **Main body:** 305 × 210 × 300 mm - **Main wheels:** Ø120 × 22 mm - **Front caster wheels:** Ø50 × 18 mm - **Vertical column:** 60 × 60 × 380 mm - **Horizontal arm:** 240 × 40 × 40 mm - **X-ray tube housing:** 100 × 85 × 90 mm - **Collimator:** 80 × 70 × 40 mm - **Handle:** 180 × 20 mm - **Control panel:** 100 × 70 × 20 mm ### Important X-ray tube arrangement The **horizontal arm extends from the vertical column and supports the X-ray tube housing at its far end**. The **X-ray tube housing must be positioned above the collimator**, with the collimator **directly attached to the bottom/front of the tube housing**. The **collimator must point vertically downward toward the patient/table**, as in a conventional mobile radiography system. Do **not** place the tube housing and collimator side-by-side or at an incorrect angle. The tube assembly should look like: **Horizontal arm → Tube housing → Collimator → downward X-ray beam direction** Include a realistic tube mounting bracket and pivot/rotation joint between the arm and tube housing. ### Mechanical structure - Vertical sliding carriage for the arm - Arm pivot and locking mechanism - Realistic wheel brackets and caster assemblies - Cable routing along the arm and column - Handle at the rear/upper part of the body - Control panel on the main body - Rounded medical-equipment enclosure
Parameters
| Name | Value | Range |
|---|---|---|
| Body Length | 305 mm | 200 – 600 |
| Body Depth | 210 mm | 150 – 400 |
| Body Height | 300 mm | 200 – 600 |
| Body Bottom Above Ground | 90 mm | 60 – 300 |
| Body Corner Fillet | 15 mm | 0 – 40 |
| Rear Main Wheel Diameter | 120 mm | 40 – 200 |
| Rear Main Wheel Width | 22 mm | 5 – 60 |
| Rear Wheel Lateral Offset | 120 mm | 60 – 200 |
| Rear Wheel Bracket Width | 30 mm | 10 – 80 |
| Rear Wheel Bracket Thickness | 8 mm | 2 – 20 |
| Front Caster Diameter | 50 mm | 20 – 120 |
| Front Caster Width | 18 mm | 5 – 40 |
| Front Caster Lateral Offset | 110 mm | 40 – 180 |
| Front Caster Bracket Width | 25 mm | 10 – 60 |
| Front Caster Bracket Thickness | 6 mm | 2 – 20 |
| Column Width | 60 mm | 30 – 120 |
| Column Depth | 60 mm | 30 – 120 |
| Column Height | 380 mm | 200 – 800 |
| Column Rear Offset | -70 mm | -200 – 200 |
| Carriage Width | 80 mm | 50 – 160 |
| Carriage Depth | 70 mm | 40 – 150 |
| Carriage Height | 60 mm | 30 – 120 |
| Carriage Slide Clearance | 2 mm | 0.5 – 10 |
| Carriage Height Position | 640 mm | 400 – 900 |
| Arm Pivot Width | 60 mm | 30 – 120 |
| Arm Pivot Depth | 50 mm | 30 – 100 |
| Arm Pivot Height | 50 mm | 30 – 100 |
| Horizontal Arm Length | 240 mm | 150 – 400 |
| Horizontal Arm Width | 40 mm | 20 – 80 |
| Horizontal Arm Height | 40 mm | 20 – 80 |
| Tube Bracket Width | 70 mm | 40 – 120 |
| Tube Bracket Depth | 50 mm | 30 – 100 |
| Tube Bracket Height | 50 mm | 30 – 100 |
| Tube Housing Width | 100 mm | 60 – 160 |
| Tube Housing Depth | 85 mm | 50 – 150 |
| Tube Housing Height | 90 mm | 50 – 160 |
| Collimator Width | 80 mm | 50 – 140 |
| Collimator Depth | 70 mm | 40 – 120 |
| Collimator Height | 40 mm | 20 – 100 |
| Handle Length | 180 mm | 100 – 300 |
| Handle Bar Diameter | 20 mm | 10 – 40 |
| Handle Height Above Body Top | 50 mm | 0 – 200 |
| Handle Post Diameter | 15 mm | 5 – 30 |
| Control Panel Width | 100 mm | 60 – 200 |
| Control Panel Thickness | 20 mm | 5 – 50 |
| Control Panel Height | 70 mm | 40 – 150 |
| Control Panel Drop From Top | 30 mm | 0 – 150 |
| Cable Conduit Width | 20 mm | 10 – 50 |
| Cable Conduit Depth | 10 mm | 5 – 30 |
| Cable Clip Count | 4 mm | 0 – 12 |
Every value above is a live dimension. Open a model like this in the editor and each one becomes a slider you can drag before exporting.
More models
Browse the full gallery →Trumpet Lyre Mount Main Body
A single 3D mechanical CAD part for a trumpet music lyre mount (Main Body with Paddle). Geometry details: 1. A 18mm-wide semi-cylindrical clamp arc for a 28mm diameter cylinder, w
UAV Ogive Nose Cone
Design a watertight, 3D-printable aerodynamic nose cone module for a fixed-wing tactical UAV, optimized for printing in Carbon Fiber Filled PETG (PETG-CF). The base of the nose con
Flat-Strap Reel Spool
Create a 3D model of a custom flat-strap reel spool for a home plate housing cavity. Geometry: - A reel spool consisting of two parallel circular outer flanges connected by a cent
PET Recycling Kiosk Frame
Design a production-ready welded steel frame for an outdoor PET bottle recycling and animal feeding kiosk. Create ONLY the steel frame. Do not create covers, motors, tanks, electr
Kugoo G2 Pro Rear Swingarm for KuKirin G4
Create a detailed 1:1 CAD drawing of custom rear swingarms for the Kugoo G2 Pro 2020 electric scooter. The swingarms must be designed to fit a KuKirin G4 hub motor instead of the o
Humanoid Robot Exploded Assembly
Design a 3D CAD model of a fully autonomous humanoid biped robot for the Robofest AI HOMO BOT competition. Dimensions Height: 800 mm (80 cm) Maximum weight: 20 kg Lightweight modu