Brackets and mounts
RPi4_Rugged_Trail_Camera_From_Scratch_Exploded
- Bounding box
- 2885.0 × 78.0 × 120.0 mm
- Engine
- Precision B-rep
- Parameters
- 40
- Published
- August 26, 2026
Download
Free to download and use. See the terms.
The prompt
Start a completely new blank CADX Studio project. Do not open, inspect, import, clone, restore, reference, trace, or reuse any existing project, model, feature tree, STEP/KCL/CAD file, uploaded file, image, or prior enclosure. Build a new native parametric assembly only from this written brief.Design a premium rugged commercial-style wildlife trail camera for a Raspberry Pi 4. Target approximately 180 × 120 × 78 mm, with a tall rounded body, layered front bezels, dark olive/forest-green/charcoal camouflage-style matte texture, matte-black trim, robust hinges and latches, removable gasketed lid, and two rear tree-strap holders for approximately 25–40 mm webbing with a textured rear rubber pad.The exact camera is not confirmed. Use a configurable Primary Camera Module — Placeholder; do not force OV5647, Camera Module v1, M12, or any specific lens claim. Use the front hierarchy of a commercial trail camera: a wide recessed upper flash/IR-illuminator placeholder panel, a prominent central circular primary camera lens with a replaceable optical window and brow hood, a separate lower-left IR/sensor opening, and a separate lower-right optional auxiliary camera/sensor bay. Do not claim that a second camera is installed; keep the auxiliary bay configurable.Re-think cooling as a complete thermal system. Separate the clean optical zone from the Pi 4 electronics/thermal zone. Mount the Pi 4 on standoffs with a conceptual heat sink or thermal spreader, then use the approximately 30 × 30 × 7 mm 5 V fan inside a protected rear/lower duct across the heat sink. Add baffled intake and exhaust paths, rain hoods, drip shields, replaceable mesh, and a conceptual hydrophobic pressure/condensation vent. Keep warm exhaust away from the camera and IR optics. Do not use large exposed vents and do not claim validated cooling or IP performance.Add a proper sealed cable gland with strain relief, status LED window, GPIO level-protection/interface board, reserved electronics space, serviceable fan and optical window, and realistic cable clearances. Keep all major parts separate and named. Generate premium front, front orthographic, rear, exploded, thermal section, optical section, internal service, and tree-mounted views. Report all assumptions, collisions, placeholder dimensions, and required optical/thermal/environmental tests. Save only as a new project named RPi4_Cool_Rugged_Wildlife_Trail_Camera_From_Scratch.
Parameters
| Name | Value | Range |
|---|---|---|
| Layout Gap | 250 mm | 200 – 400 |
| Body Width | 180 mm | 150 – 220 |
| Body Depth | 78 mm | 60 – 100 |
| Body Height | 120 mm | 90 – 160 |
| Shell Wall Thickness | 6 mm | 2 – 12 |
| Front Bezel Width | 175 mm | 150 – 200 |
| Front Bezel Thickness | 8 mm | 4 – 15 |
| Front Bezel Height | 115 mm | 90 – 150 |
| Optical Window Diameter | 45 mm | 30 – 60 |
| Optical Window Thickness | 3 mm | 2 – 6 |
| Brow Hood Width | 60 mm | 40 – 80 |
| Brow Hood Depth | 18 mm | 10 – 30 |
| Brow Hood Height | 12 mm | 6 – 20 |
| Flash/IR Panel Width | 140 mm | 100 – 180 |
| Flash/IR Panel Thickness | 8 mm | 4 – 15 |
| Flash/IR Panel Height | 25 mm | 15 – 40 |
| LED Hole Diameter | 5 mm | 2 – 8 |
| LED Hole Count | 6 mm | 1 – 12 |
| IR Sensor Opening Diameter | 20 mm | 12 – 30 |
| IR Sensor Recess Depth | 8 mm | 4 – 15 |
| Auxiliary Bay Cover Size | 35 mm | 25 – 50 |
| Auxiliary Bay Cover Thickness | 6 mm | 3 – 10 |
| Removable Lid Width | 180 mm | 150 – 220 |
| Removable Lid Depth | 78 mm | 60 – 100 |
| Removable Lid Height | 10 mm | 6 – 20 |
| Strap Holder Width | 50 mm | 35 – 70 |
| Strap Holder Depth | 12 mm | 6 – 20 |
| Strap Holder Height | 60 mm | 40 – 80 |
| Strap Slot Width | 30 mm | 20 – 45 |
| Strap Slot Height | 40 mm | 25 – 60 |
| Rear Rubber Pad Width | 160 mm | 120 – 200 |
| Rear Rubber Pad Height | 60 mm | 40 – 80 |
| Rear Rubber Pad Thickness | 5 mm | 2 – 10 |
| Pi Mounting Plate Width | 90 mm | 70 – 110 |
| Pi Mounting Plate Depth | 65 mm | 50 – 80 |
| Pi Mounting Plate Thickness | 3 mm | 2 – 6 |
| Standoff Height | 6 mm | 3 – 15 |
| Standoff Diameter | 5 mm | 3 – 8 |
| Standoff Spacing X | 58 mm | 30 – 80 |
| Standoff Spacing Y | 49 mm | 30 – 60 |
Every value above is a live dimension. Open a model like this in the editor and each one becomes a slider you can drag before exporting.
More models
Browse the full gallery →Trumpet Lyre Mount Main Body
A single 3D mechanical CAD part for a trumpet music lyre mount (Main Body with Paddle). Geometry details: 1. A 18mm-wide semi-cylindrical clamp arc for a 28mm diameter cylinder, w
UAV Ogive Nose Cone
Design a watertight, 3D-printable aerodynamic nose cone module for a fixed-wing tactical UAV, optimized for printing in Carbon Fiber Filled PETG (PETG-CF). The base of the nose con
Flat-Strap Reel Spool
Create a 3D model of a custom flat-strap reel spool for a home plate housing cavity. Geometry: - A reel spool consisting of two parallel circular outer flanges connected by a cent