Brackets and mounts
Retro Wayfarer Smart Glasses Assembly
- Bounding box
- 145.0 × 193.0 × 50.0 mm
- Engine
- Precision B-rep
- Parameters
- 51
- Published
- August 9, 2026
Download
Free to download and use. See the terms.
The prompt
Outer Frame SilhouetteStyle: Bold, chunky retro Wayfarer silhouette.Material: 3K twill matte carbon fiber sheets.Finish: Seamless weave with clean mechanical lines.Thickness: 8 mm to 10 mm wide temple arms.Exterior: Zero visible buttons, LEDs, or ports.🦿 Left Arm Internal CavitiesPurpose: Power storage and visual projection engine.Front hinge: Hollow cylindrical projector barrel pocket.Hinge corner: Microscopic open-air optical window cutout.Middle spine: Flat rectangular voltage regulator slot.Ear hook: Deep cylindrical dual battery tunnel.🦿 Right Arm Internal CavitiesPurpose: Computer processing brain and audio output.Main wall: Flat rectangular motherboard pocket.Inner edge: Flush-cut horizontal SIM tray slit.Outer wall: Radio-transparent non-carbon antenna window.Ear tip: Flat circular bone conduction indentation.👃 Nose Bridge PathwayLocation: Interior top rim of the frames.Channel: 1 mm deep micro-groove carved horizontally.Function: Hides cross-frame wiring out of sight.Sealing: Covered completely with black carbon filler.👁️ Optical Alignment GeometryLayout: Engine sits parallel to left temple.Direction: Projector fires light straight forward.Target: 12 mm clear circular film patch.Placement: Adhered to interior left lens surface.Reflection: Precise 90-degree backward bounce into pupil.Calibration: 3D micro ball-joint adjustment bracket cavity.🛡️ Mechanical Insulation SystemLining: 0.5 mm non-conductive interior sleeves.Function: Isolates boards from conductive carbon walls.Closure: Ultra-thin snap-on inner arm cover plates.💡
Parameters
| Name | Value | Range |
|---|---|---|
| Frame Bottom Width | 140 mm | 120 – 180 |
| Frame Top Width | 100 mm | 80 – 140 |
| Frame Height | 50 mm | 40 – 70 |
| Frame Thickness | 8 mm | 5 – 15 |
| Lens Opening Width | 55 mm | 40 – 70 |
| Lens Opening Height | 40 mm | 30 – 50 |
| Lens Corner Radius | 5 mm | 2 – 10 |
| Nose Bridge Width | 20 mm | 15 – 30 |
| Outer Margin | 5 mm | 2 – 10 |
| Nose Groove Width | 25 mm | 15 – 30 |
| Nose Groove Depth | 1 mm | 0.5 – 2 |
| Nose Groove Height | 3 mm | 2 – 5 |
| Hinge Offset from Edge | 2 mm | 1 – 5 |
| Hinge Pin Radius | 2 mm | 1 – 4 |
| Hinge Pin Length | 4 mm | 2 – 8 |
| Temple Arm Length | 150 mm | 120 – 180 |
| Arm Width (X) | 10 mm | 6 – 14 |
| Arm Height (Z) | 12 mm | 8 – 16 |
| Projector Pocket Diameter | 12 mm | 8 – 20 |
| Projector Pocket Depth | 20 mm | 10 – 35 |
| Projector Pocket Start from Front | 5 mm | 2 – 15 |
| Voltage Reg. Slot Length | 30 mm | 20 – 50 |
| Voltage Reg. Slot Depth (X) | 8 mm | 4 – 12 |
| Voltage Reg. Slot Height | 6 mm | 4 – 10 |
| Voltage Reg. Slot Y Position | 70 mm | 40 – 100 |
| Battery Tunnel Radius | 3 mm | 2 – 5 |
| Battery Tunnel Depth | 40 mm | 20 – 60 |
| Battery Tunnel Spacing | 5 mm | 4 – 8 |
| Battery Tunnel Y Start | 110 mm | 80 – 130 |
| Cover Plate Thickness | 0.5 mm | 0.2 – 1 |
| Motherboard Pocket Length | 80 mm | 50 – 120 |
| Motherboard Pocket Depth | 8 mm | 4 – 12 |
| Motherboard Pocket Height | 10 mm | 6 – 14 |
| Motherboard Y Start | 15 mm | 5 – 40 |
| SIM Slit Length | 15 mm | 10 – 25 |
| SIM Slit Depth | 2 mm | 1 – 4 |
| SIM Slit Height | 1 mm | 0.5 – 2 |
| SIM Slit Y Position | 50 mm | 20 – 80 |
| Antenna Window Length | 20 mm | 10 – 30 |
| Antenna Window Depth | 2 mm | 1 – 4 |
| Antenna Window Height | 2 mm | 1 – 4 |
| Antenna Window Y Position | 80 mm | 40 – 120 |
| Bone Conduction Diameter | 15 mm | 10 – 20 |
| Bone Conduction Depth | 1 mm | 0.5 – 2 |
| Bone Conduction Y Position | 145 mm | 120 – 160 |
| Projector Engine Diameter | 12 mm | 8 – 18 |
| Projector Engine Length | 20 mm | 15 – 30 |
| Left Lens Thickness | 2 mm | 1 – 3 |
| Right Lens Thickness | 2 mm | 1 – 3 |
| Film Patch Diameter | 12 mm | 8 – 20 |
| Insulation Sleeve Thickness | 0.5 mm | 0.2 – 1 |
Every value above is a live dimension. Open a model like this in the editor and each one becomes a slider you can drag before exporting.
More models
Browse the full gallery →Trumpet Lyre Mount Main Body
A single 3D mechanical CAD part for a trumpet music lyre mount (Main Body with Paddle). Geometry details: 1. A 18mm-wide semi-cylindrical clamp arc for a 28mm diameter cylinder, w
UAV Ogive Nose Cone
Design a watertight, 3D-printable aerodynamic nose cone module for a fixed-wing tactical UAV, optimized for printing in Carbon Fiber Filled PETG (PETG-CF). The base of the nose con
Flat-Strap Reel Spool
Create a 3D model of a custom flat-strap reel spool for a home plate housing cavity. Geometry: - A reel spool consisting of two parallel circular outer flanges connected by a cent