Gears and transmission
Quadcopter Central Frame
- Bounding box
- 200.0 × 160.0 × 16.0 mm
- Engine
- Precision B-rep
- Parameters
- 20
- Published
- October 12, 2026
Download
Free to download and use. See the terms.
The prompt
Create only the central frame of a non-functional, display-only tilt-rotor quadcopter model, designed for separate FDM printing and tool-free assembly. Use millimeters. The printer bed is 220 × 220 mm. The central frame must fit entirely within a 200 × 160 mm footprint. Do not create arms, propellers, motor pods, tilt joints, landing gear, or the upper enclosure yet. Do not add electronics mounts, battery compartments, screw holes, bolts, nuts, or threads. Coordinate system: X is front-to-back, Y is left-to-right, and Z is upward. Center the frame at X=0, Y=0. Place its bottom at Z=0. Create the following geometry: A rounded rectangular perimeter ring, 200 mm along X and 160 mm along Y, with a ring width of 16 mm, a thickness of 6 mm, and an outer corner radius of 12 mm. A central plate, 100 × 70 mm and 6 mm thick, centered on the origin. Four arm mounting pads, each 36 mm along X and 32 mm along Y, extending from Z=0 to Z=16 mm. Place their centers at (+65,+58), (+65,-58), (-65,+58), and (-65,-58) mm. Four diagonal connecting ribs, 14 mm wide in the XY plane and 6 mm thick. Connect the central plate to the four arm mounting pads with positive solid overlap. Four landing gear socket blocks, each 18 mm along X and 22 mm along Y, extending from Z=0 to Z=14 mm. Place their centers at (+30,+69), (+30,-69), (-30,+69), and (-30,-69) mm. Fuse these blocks into the perimeter ring. Leave the spaces between the central plate, ribs, and perimeter ring open through the frame. Fuse all features into one connected solid. Keep the bottom coplanar at Z=0 and preserve symmetry about the XZ and YZ planes. Do not create any sockets yet. Do not add decorative details or edge fillets yet. Make the principal dimensions editable parameters.
Parameters
| Name | Value | Range |
|---|---|---|
| Ring Overall Length (X) | 200 mm | 120 – 200 |
| Ring Overall Width (Y) | 160 mm | 100 – 160 |
| Ring Wall Width | 16 mm | 8 – 30 |
| Ring Thickness | 6 mm | 3 – 12 |
| Outer Corner Radius | 12 mm | 2 – 30 |
| Central Plate Length (X) | 100 mm | 40 – 160 |
| Central Plate Width (Y) | 70 mm | 30 – 120 |
| Central Plate Thickness | 6 mm | 3 – 12 |
| Arm Pad Length (X) | 36 mm | 16 – 60 |
| Arm Pad Width (Y) | 32 mm | 16 – 60 |
| Arm Pad Height (Z) | 16 mm | 6 – 40 |
| Arm Pad Center Offset X | 65 mm | 20 – 90 |
| Arm Pad Center Offset Y | 58 mm | 20 – 75 |
| Rib Width (XY) | 14 mm | 6 – 30 |
| Rib Thickness | 6 mm | 3 – 12 |
| Socket Block Length (X) | 18 mm | 8 – 40 |
| Socket Block Width (Y) | 22 mm | 8 – 40 |
| Socket Block Height (Z) | 14 mm | 4 – 30 |
| Socket Block Center Offset X | 30 mm | 0 – 80 |
| Socket Block Center Offset Y | 69 mm | 20 – 79 |
Every value above is a live dimension. Open a model like this in the editor and each one becomes a slider you can drag before exporting.
More models
Browse the full gallery →Spur Gearbox
design gearbox
Involute Spur Gear with Keyway
Precision Involute Spur Gear with Hub and Keyway: Module (m) of 2.0 mm, 40 teeth (z), Pitch Circle Diameter (d) of 80.00 mm, 20° pressure angle (\alpha), 15.00 mm face width (b), a
Parametric Helical Gear
Create a parametric helical gear with the following specifications: 32 teeth, normal module of 3 mm, right-hand helix, total face width of 80 mm, and a central bore hole with a dia
Rod with Spur Gear
Metal rod diameter is 20 mm and length is 100 mm and right side attach a gear and their OD is 50 mm
Spur Gear (12 Teeth)
Built a gear with 12 teeth
Two-Stage Spur Gear Reduction Assembly
Design a 2-stage spur gear reduction set for 3D printing with an overall 10:1 ratio. Stage 1: A 12-tooth pinion driving a 36-tooth gear (3:1). Stage 2: A 12-tooth pinion coupled