Brackets and mounts
Pacifier Shield + Kickstand Ring
- Bounding box
- 410.1 × 139.9 × 22.1 mm
- Engine
- Precision B-rep
- Parameters
- 35
- Published
- August 12, 2026
Download
Free to download and use. See the terms.
The prompt
Create two separate 3D CAD solid models (output as distinct components) for a 3D-printable giant pacifier iPhone 16 Pro case and desk mount accessory, designed for 2.85mm PLA FDM printing with 0.3mm to 0.4mm mechanical clearance gaps on all interlocking surfaces. Component 1: Main Shield and Phone Dock Body - Outer Geometry: Symmetrical curved butterfly pacifier shield shape, 220mm total width, 140mm total height, and 12mm thickness, with smooth rounded fillet chamfers on all outer edges. - Aesthetic Venting: Four symmetrical curved airflow vent slots cut through the shield body (two upper, two lower) for pure aesthetics. - Rear Phone Dock: On the flat rear face, a centered rectangular recessed cavity measuring 150.0mm length x 72.0mm width x 8.5mm depth to fit an iPhone 16 Pro with drop-in simplicity. Inside this cavity, add a recessed square camera bump pocket measuring 38.5mm x 38.5mm x 2.5mm depth to allow the lens module to sit flat. - Bottom Openings: Open cutouts on the bottom edge of the recess for standard USB-C cable access and speaker grilles. - Central Front Boss: On the front face center, a smooth low-profile flat circular cap housing (50mm diameter) integrating a cylindrical pivot pin socket with built-in internal ratchet teeth/detents for 0-degree, 45-degree, and 90-degree locking positions. Component 2: Hinged Kickstand Ring - Ring Geometry: A thick, rounded semi-circular handle ring with an outer diameter of 80mm, an inner grip diameter of 55mm, and a ring cross-section thickness of 12mm, featuring fully rounded ergonomic edges. - Hinge Interface: At the anchor point of the ring, design an integrated pivot knuckle with matching internal detent pins engineered to lock securely into the Main Shield's 0°, 45°, and 90° ratchet angles, allowing the ring to pivot freely and hold position as a desk kickstand. Ensure all geometries are watertight, manifold solids with clean clearance tolerances. Output units: Millimeters.
Parameters
| Name | Value | Range |
|---|---|---|
| Shield Width | 220 mm | 100 – 400 |
| Shield Height | 140 mm | 80 – 300 |
| Shield Thickness | 12 mm | 4 – 30 |
| Phone Dock Width | 150 mm | 100 – 220 |
| Phone Dock Height | 72 mm | 60 – 140 |
| Phone Dock Depth | 8.5 mm | 3 – 11 |
| Camera Pocket Size | 38.5 mm | 20 – 80 |
| Camera Pocket Depth | 2.5 mm | 1 – 5 |
| Camera Pocket Y Offset | 0 mm | -20 – 20 |
| USB-C Cutout Width | 14 mm | 8 – 30 |
| USB-C Cutout Height | 34 mm | 10 – 50 |
| Speaker Cutout Width | 6 mm | 3 – 12 |
| Speaker Cutout Height | 28 mm | 10 – 50 |
| Speaker Cutout Spacing | 56 mm | 30 – 80 |
| Vent Slot Width | 8 mm | 3 – 20 |
| Vent Slot Height | 20 mm | 5 – 45 |
| Vent Slot X Offset | 55 mm | 25 – 90 |
| Vent Slot Y Offset | 50 mm | 25 – 65 |
| Pivot Boss Diameter | 50 mm | 25 – 80 |
| Pivot Boss Height | 10 mm | 4 – 20 |
| Pivot Bore Diameter | 20 mm | 8 – 40 |
| Pivot Bore Depth | 12 mm | 5 – 20 |
| Detent Hole Diameter | 3 mm | 1.5 – 6 |
| Detent Hole Depth | 3 mm | 1 – 6 |
| Detent Pattern Radius | 15 mm | 8 – 22 |
| Ring Outer Diameter | 80 mm | 50 – 140 |
| Ring Inner Grip Diameter | 55 mm | 25 – 120 |
| Ring Cross-Section Thickness | 12 mm | 4 – 30 |
| Knuckle Width | 20 mm | 10 – 50 |
| Knuckle Height | 15 mm | 6 – 40 |
| Knuckle Pivot Hole Diameter | 8 mm | 3 – 16 |
| Ring Detent Pattern Radius | 5 mm | 3 – 15 |
| Ring Detent Pin Diameter | 3 mm | 1.5 – 6 |
| Ring Detent Pin Height | 3 mm | 1 – 6 |
| Exploded Layout X Gap | 260 mm | 180 – 500 |
Every value above is a live dimension. Open a model like this in the editor and each one becomes a slider you can drag before exporting.
More models
Browse the full gallery →Trumpet Lyre Mount Main Body
A single 3D mechanical CAD part for a trumpet music lyre mount (Main Body with Paddle). Geometry details: 1. A 18mm-wide semi-cylindrical clamp arc for a 28mm diameter cylinder, w
UAV Ogive Nose Cone
Design a watertight, 3D-printable aerodynamic nose cone module for a fixed-wing tactical UAV, optimized for printing in Carbon Fiber Filled PETG (PETG-CF). The base of the nose con
Flat-Strap Reel Spool
Create a 3D model of a custom flat-strap reel spool for a home plate housing cavity. Geometry: - A reel spool consisting of two parallel circular outer flanges connected by a cent