Brackets and mounts
Motor + ESC Mount Assembly (Exploded)
- Bounding box
- 5012.8 × 381.0 × 45.0 mm
- Engine
- Precision B-rep
- Parameters
- 60
- Published
- October 26, 2026
Download
Free to download and use. See the terms.
The prompt
Design a motor + ESC mount assembly for a 20 mm OD / 18 mm ID carbon-fibre tube arm. Units: mm. Parametric, cleanly named features, STEP export. REFERENCE PARTS (simplified): - Tube: OD 20, ID 18, length 250. - Motor (T-Motor MN4006): cylinder Ø44.35 x 21 tall, 4xM3 holes on [CONFIRM from T-Motor drawing: assume 16 x 16 pattern], shaft Ø4, prop adapter 6. - Prop: 15" disc, Ø381, 5 mm thick, placed above the motor. Used for clearance checks only. - ESC (T-Motor Air 40A): block [ASSUMED 60 x 25 x 12 until datasheet confirmed]. CUSTOM PARTS: 1. Motor clamp, lower half: Al 6061-T6. Saddle of Ø20 H8 for the tube, 2 mm wall, 24 mm long along the tube, 2x M3 clamp screws on the split line (clearance Ø3.4, counterbore for socket head). One M3 cross-hole through the tube axis for the anti-rotation bolt. Top face is a motor plate, 3 mm thick, with 4x M3 tapped holes and a Ø12 centre relief. Add fillets R2 on all outside corners and lightening cut-outs. 2. Motor clamp, upper half: mirrors the lower, with the same M3 cross-hole and clamp-screw bosses. 3. Internal plug: Al 6061, Ø17.9 x 20 long, bonded into the tube end with epoxy. M3 cross-hole, 1 mm wall around it. 4. ESC bracket: clip-on half-clamp on the tube (Ø20), 2x M3 screws, flat pad 60 x 25 with 2 zip-tie slots (3 x 1.5). Located 70 mm inboard of the motor axis, on the side of the tube. Minimum 3 mm air gap under the ESC. FASTENERS (simple models): M3x16 clamp screws (x2), M3x25 cross-bolt with nyloc, M3x6 motor screws (x4). Check head clearance and tool access. ASSEMBLY: place the motor axis at the tube end, perpendicular to the tube. Run an interference/clearance check. Nothing within the 15" prop disc except the motor. Cable path along the underside of the tube, bend radius at least 15 mm. OUTPUTS: assembly + part files, an isometric view, an exploded view, mass of each custom part, dimensioned drawings (material, tolerances, thread callouts), STEP of the full assembly.
Parameters
| Name | Value | Range |
|---|---|---|
| Exploded Layout Gap | 500 mm | 100 – 1000 |
| Tube OD | 20 mm | 10 – 40 |
| Tube ID | 18 mm | 5 – 35 |
| Tube Length | 250 mm | 50 – 500 |
| Motor Diameter | 44.35 mm | 20 – 80 |
| Motor Height | 21 mm | 5 – 50 |
| Motor Shaft Diameter | 4 mm | 2 – 10 |
| Motor Shaft Length | 8 mm | 0 – 30 |
| Prop Adapter Diameter | 6 mm | 3 – 15 |
| Prop Adapter Height | 4 mm | 0 – 20 |
| Motor Mount Pitch | 16 mm | 8 – 40 |
| Motor Mount Hole Dia | 3 mm | 1.5 – 6 |
| Prop Clearance Disc Dia | 381 mm | 100 – 600 |
| Prop Clearance Disc Thickness | 5 mm | 1 – 20 |
| ESC Length | 60 mm | 20 – 120 |
| ESC Width | 25 mm | 10 – 60 |
| ESC Height | 12 mm | 3 – 30 |
| Clamp Length Along Tube | 24 mm | 10 – 60 |
| Clamp Wall Thickness | 2 mm | 1 – 8 |
| Motor Plate Thickness | 3 mm | 1 – 10 |
| Motor Plate X Size | 30 mm | 10 – 80 |
| Motor Plate Y Size | 40 mm | 10 – 80 |
| Motor Plate Mount Pitch | 16 mm | 6 – 40 |
| Motor Plate Mount Hole Dia | 3 mm | 1.5 – 6 |
| Centre Relief Dia | 12 mm | 4 – 30 |
| Clamp Screw Clearance Dia | 3.4 mm | 2 – 8 |
| Clamp Counterbore Dia | 6 mm | 3 – 12 |
| Clamp Counterbore Depth | 3 mm | 0.5 – 10 |
| Clamp Boss Dia | 6 mm | 3 – 15 |
| Clamp Boss Height | 4 mm | 1 – 15 |
| Clamp Boss Y Offset | 14 mm | 0 – 30 |
| Cross Hole Dia | 3.4 mm | 1.5 – 8 |
| Cross Hole X Position | 20 mm | 0 – 60 |
| Outside Fillet Radius | 1.5 mm | 0 – 4 |
| Lightening Hole Dia | 4 mm | 1 – 12 |
| Lightening Hole X1 | 6 mm | 0 – 60 |
| Lightening Hole X2 | 18 mm | 0 – 60 |
| Tube Plug Diameter | 17.9 mm | 5 – 35 |
| Tube Plug Length | 20 mm | 5 – 60 |
| Plug Cross Hole Dia | 3.4 mm | 1.5 – 8 |
| Plug Cross Hole X | 10 mm | 0 – 60 |
| ESC Clamp Length | 20 mm | 5 – 60 |
| ESC Pad Length | 60 mm | 20 – 120 |
| ESC Pad Width | 25 mm | 10 – 60 |
| ESC Pad Thickness | 3 mm | 1 – 10 |
| ESC Bracket Screw Hole Dia | 3.4 mm | 1.5 – 8 |
| ESC Bracket Hole X1 | 6 mm | 0 – 60 |
| ESC Bracket Hole X2 | 14 mm | 0 – 60 |
| Zip Tie Slot Length | 3 mm | 1 – 10 |
| Zip Tie Slot Width | 1.5 mm | 0.5 – 5 |
| Zip Tie Slot Spacing | 20 mm | 5 – 50 |
| Fastener Shank Dia | 3 mm | 1.5 – 8 |
| Fastener Head Dia | 5.5 mm | 3 – 15 |
| Clamp Screw Head Height | 3 mm | 1 – 10 |
| Clamp Screw Length | 16 mm | 5 – 40 |
| Cross Bolt Length | 25 mm | 10 – 60 |
| Nyloc Nut Across Flats | 5.5 mm | 3 – 15 |
| Nyloc Nut Height | 2.4 mm | 1 – 10 |
| Motor Screw Head Height | 2.5 mm | 1 – 8 |
| Motor Screw Length | 6 mm | 2 – 20 |
Every value above is a live dimension. Open a model like this in the editor and each one becomes a slider you can drag before exporting.
More models
Browse the full gallery →Trumpet Lyre Mount Main Body
A single 3D mechanical CAD part for a trumpet music lyre mount (Main Body with Paddle). Geometry details: 1. A 18mm-wide semi-cylindrical clamp arc for a 28mm diameter cylinder, w
UAV Ogive Nose Cone
Design a watertight, 3D-printable aerodynamic nose cone module for a fixed-wing tactical UAV, optimized for printing in Carbon Fiber Filled PETG (PETG-CF). The base of the nose con
Flat-Strap Reel Spool
Create a 3D model of a custom flat-strap reel spool for a home plate housing cavity. Geometry: - A reel spool consisting of two parallel circular outer flanges connected by a cent
PET Recycling Kiosk Frame
Design a production-ready welded steel frame for an outdoor PET bottle recycling and animal feeding kiosk. Create ONLY the steel frame. Do not create covers, motors, tanks, electr
Kugoo G2 Pro Rear Swingarm for KuKirin G4
Create a detailed 1:1 CAD drawing of custom rear swingarms for the Kugoo G2 Pro 2020 electric scooter. The swingarms must be designed to fit a KuKirin G4 hub motor instead of the o
Humanoid Robot Exploded Assembly
Design a 3D CAD model of a fully autonomous humanoid biped robot for the Robofest AI HOMO BOT competition. Dimensions Height: 800 mm (80 cm) Maximum weight: 20 kg Lightweight modu