Brackets and mounts
Mobile Electrical Enclosure (560x450x850)
- Bounding box
- 560.0 × 450.0 × 860.0 mm
- Engine
- Precision B-rep
- Parameters
- 34
- Published
- October 13, 2026
Download
Free to download and use. See the terms.
The prompt
Create a parametric sheet metal mobile electrical enclosure assembly with dimensions 560mm width, 450mm depth, and 850mm height, constructed from 3mm aluminum sheet with 20mm internal mounting return flanges. Features to model: 1. Main cabinet body with an open front: left wall, right wall, top cover plate, reinforced bottom base plate with welded 25mm structural cross-ribs, and solid rear panel. 2. A fixed horizontal sheet metal divider shelf (3mm thick with 25mm downward stiffener flanges on all four edges), positioned 360mm above the base plate, dividing the battery bay (360mm clearance) from the upper bay (428mm clearance). 3. Two vertical guide U-channels (15mm wide x 15mm deep x 2mm wall thickness) fastened vertically to the inner front edges of the left and right side walls, running from the base plate to the divider shelf. 4. A removable lower slide-out front sheet panel (3mm thick, 360mm high, with a folded 15mm top return handle flange) seated inside the side guide U-channels that slides vertically upward and out. 5. An upper front sheet door (3mm thick) hinged at the top edge via a continuous piano hinge, featuring a folded 20mm bottom overlap lip that covers and locks the top edge of the lower slide-out panel when shut. 6. A circular bulkhead inlet cutout (58mm diameter) with four 4.5mm mounting holes on a 65mm bolt circle on the upper exterior right wall, centered 600mm from the floor and 100mm from the rear corner. 7. Two 120mm square ventilation fan/grille cutouts (115mm center-to-center hole pattern with 4.5mm corner holes): an intake cutout positioned low on the upper bay left wall, and an exhaust cutout positioned high on the upper bay right wall. 8. Two pairs of battery tie-down strap slots (35mm long x 8mm wide with fully rounded 4mm radiused ends) laser-cut into the bottom base plate, spaced 320mm front-to-back and 200mm side-to-side. 9. Four caster mounting plate pads (90mm x 90mm with four 9mm bolt holes) welded/fastened beneath the exterior bottom corners of the base plate.
Parameters
| Name | Value | Range |
|---|---|---|
| Cabinet Width | 560 mm | 300 – 1200 |
| Cabinet Depth | 450 mm | 300 – 1000 |
| Cabinet Height | 850 mm | 400 – 2000 |
| Sheet Thickness | 3 mm | 1 – 6 |
| Mounting Return Flange | 20 mm | 5 – 50 |
| Cross-Rib Height | 25 mm | 5 – 60 |
| Cross-Rib Width | 10 mm | 3 – 30 |
| Divider Above Base Plate | 360 mm | 100 – 800 |
| Shelf Stiffener Depth | 25 mm | 5 – 60 |
| Guide Channel Width | 15 mm | 5 – 40 |
| Guide Channel Depth | 15 mm | 5 – 40 |
| Guide Channel Wall | 2 mm | 1 – 5 |
| Lower Slide Panel Height | 360 mm | 100 – 700 |
| Handle Return Flange | 15 mm | 5 – 50 |
| Door Overlap Lip | 20 mm | 5 – 60 |
| Piano Hinge Diameter | 8 mm | 3 – 20 |
| Bulkhead Inlet Diameter | 58 mm | 20 – 150 |
| Bulkhead Height From Floor | 600 mm | 100 – 1600 |
| Bulkhead From Rear Corner | 100 mm | 30 – 400 |
| Bolt Circle Diameter | 65 mm | 20 – 200 |
| Bolt Hole Diameter | 4.5 mm | 2 – 12 |
| Fan Cutout Square | 120 mm | 40 – 300 |
| Fan Hole Spacing | 115 mm | 20 – 280 |
| Fan Hole Diameter | 4.5 mm | 2 – 10 |
| Intake Fan Height | 450 mm | 50 – 800 |
| Exhaust Fan Height | 720 mm | 50 – 800 |
| Strap Slot Length | 35 mm | 10 – 100 |
| Strap Slot Width | 8 mm | 3 – 30 |
| Slot Spacing Side-to-Side | 200 mm | 50 – 500 |
| Slot Spacing Front-to-Back | 320 mm | 50 – 400 |
| Caster Pad Size | 90 mm | 40 – 200 |
| Caster Pad Thickness | 10 mm | 3 – 30 |
| Caster Bolt Hole Diameter | 9 mm | 3 – 20 |
| Caster Bolt Spacing | 64 mm | 20 – 160 |
Every value above is a live dimension. Open a model like this in the editor and each one becomes a slider you can drag before exporting.
More models
Browse the full gallery →Trumpet Lyre Mount Main Body
A single 3D mechanical CAD part for a trumpet music lyre mount (Main Body with Paddle). Geometry details: 1. A 18mm-wide semi-cylindrical clamp arc for a 28mm diameter cylinder, w
UAV Ogive Nose Cone
Design a watertight, 3D-printable aerodynamic nose cone module for a fixed-wing tactical UAV, optimized for printing in Carbon Fiber Filled PETG (PETG-CF). The base of the nose con
Flat-Strap Reel Spool
Create a 3D model of a custom flat-strap reel spool for a home plate housing cavity. Geometry: - A reel spool consisting of two parallel circular outer flanges connected by a cent
PET Recycling Kiosk Frame
Design a production-ready welded steel frame for an outdoor PET bottle recycling and animal feeding kiosk. Create ONLY the steel frame. Do not create covers, motors, tanks, electr
Kugoo G2 Pro Rear Swingarm for KuKirin G4
Create a detailed 1:1 CAD drawing of custom rear swingarms for the Kugoo G2 Pro 2020 electric scooter. The swingarms must be designed to fit a KuKirin G4 hub motor instead of the o
Humanoid Robot Exploded Assembly
Design a 3D CAD model of a fully autonomous humanoid biped robot for the Robofest AI HOMO BOT competition. Dimensions Height: 800 mm (80 cm) Maximum weight: 20 kg Lightweight modu