Brackets and mounts
Mobile Container Material Separation System
- Bounding box
- 7308.1 × 2619.0 × 4396.1 mm
- Engine
- Precision B-rep
- Parameters
- 63
- Published
- October 28, 2026
Download
Free to download and use. See the terms.
The prompt
A professional engineering layout drawing of a mobile material separation system enclosed within a standard 20ft High Cube ISO shipping container (Internal dimensions: length 5.90m, width 2.35m, height 2.70m). The layout must include both a SECTION VIEW (side profile) and a PLAN VIEW (top-down blueprint), presented in a clean, black-and-white patent illustration style with technical dimension lines and annotations. SECTION VIEW (Side Profile): Show a vertical gravity-fed separation line. On top of the container roof, a big-bag support structure holds a large bulk bag (storsäck). A mechanically sealed discharge spout passes vertically through a reinforced hole in the container roof. Attached to this top spout is an industrial vibrator for material discharge assist, connected via a flexible rubber compensator joint to isolate vibrations. Directly underneath the roof penetration inside the container, the material flows into an intake hopper, followed by a controlled horizontal screw conveyor. The screw conveyor feeds into an enclosed mechanical siktmaskin (vibratory screening machine) featuring a 5mm coarse screen deck and a 1mm fine screen deck. Material over 5mm is discharged via a horizontal rotary valve (cellsluss) into a negative-pressure steel waste bucket. Material under 1mm (fine lead dust) falls into a bottom trough and is channeled to the same negative-pressure bucket. The target fraction of 1-4mm rubber granules continues into a vertical vacuum classifier (vacuumsug) for density separation, where heavy projectile metal debris is separated into a second negative-pressure steel bucket. The clean rubber granules are collected by a pneumatic grain conveyor (sädestransportör) at the floor level. PLAN VIEW (Top-Down Blueprint): Show the entire 6-meter length of the 20ft container. The entire machinery line (intake hopper, screw conveyor, enclosed screening machine, vacuum classifier, and pneumatic conveyor) is mounted sequentially along one longitudinal wall of the container. The opposite side of the container width is kept completely clear as a continuous 1.2-meter wide operator service walkway, stretching from the main container double doors at one end to the filtration area at the other. The layout shows the pneumatic conveyor's blower unit and primary cyclone inside the container, with an air discharge line leading out to an external secondary cyclone with a diverter valve (pant-leg chute) hanging outside for dual big-bag collection. The return exhaust air line is routed to an indoor multi-stage air filtration box containing a coarse pre-filter and a final HEPA absolute filter before venting clean air. The overall style must be a highly accurate, scaled, parametric blueprint layout with minimal visual noise, clear arrows for material flow direction, and separate callouts for "Main Granule Flow", "Metal Waste Collection", and "HEPA Air Ventilation".
Parameters
| Name | Value | Range |
|---|---|---|
| Container Length | 6058 mm | 4000 – 8000 |
| Container Width | 2438 mm | 1800 – 3200 |
| Container Height | 2896 mm | 2000 – 3500 |
| Wall Thickness | 50 mm | 10 – 100 |
| Floor Thickness | 100 mm | 20 – 200 |
| Roof Thickness | 50 mm | 10 – 100 |
| Roof Opening Size | 700 mm | 300 – 1200 |
| Roof Opening X | -2400 mm | -3000 – 0 |
| Roof Opening Y | -800 mm | -1100 – 0 |
| Door Thickness | 50 mm | 10 – 100 |
| Door Height | 2500 mm | 1500 – 2800 |
| Roof Frame Length | 1200 mm | 600 – 2000 |
| Roof Frame Width | 1200 mm | 600 – 2000 |
| Roof Frame Height | 1500 mm | 800 – 2500 |
| Frame Post Size | 80 mm | 30 – 150 |
| Bulk Bag Diameter | 900 mm | 400 – 1400 |
| Bulk Bag Height | 1200 mm | 500 – 2000 |
| Spout Diameter | 250 mm | 100 – 500 |
| Spout Height | 600 mm | 200 – 1000 |
| Vibrator Length | 200 mm | 80 – 400 |
| Vibrator Width | 150 mm | 60 – 300 |
| Vibrator Height | 150 mm | 60 – 300 |
| Compensator Diameter | 300 mm | 120 – 600 |
| Compensator Height | 200 mm | 80 – 400 |
| Hopper Top Length | 800 mm | 400 – 1400 |
| Hopper Top Width | 700 mm | 400 – 1200 |
| Hopper Height | 600 mm | 300 – 1200 |
| Hopper Outlet Diameter | 250 mm | 100 – 500 |
| Screw Conveyor Length | 2500 mm | 1200 – 4000 |
| Screw Conveyor Diameter | 300 mm | 150 – 600 |
| Drive Unit Length | 400 mm | 150 – 800 |
| Drive Unit Width | 300 mm | 150 – 600 |
| Drive Unit Height | 400 mm | 150 – 800 |
| Screening Machine Length | 1800 mm | 800 – 3000 |
| Screening Machine Width | 900 mm | 400 – 1500 |
| Screening Machine Height | 1200 mm | 600 – 2000 |
| Rotary Valve Length | 250 mm | 120 – 500 |
| Rotary Valve Width | 250 mm | 120 – 500 |
| Rotary Valve Height | 300 mm | 120 – 600 |
| Waste Bucket Length | 500 mm | 250 – 900 |
| Waste Bucket Width | 500 mm | 250 – 900 |
| Waste Bucket Height | 700 mm | 300 – 1200 |
| Vacuum Classifier Diameter | 700 mm | 300 – 1200 |
| Vacuum Classifier Height | 1500 mm | 600 – 2500 |
| Blower Length | 600 mm | 250 – 1000 |
| Blower Width | 400 mm | 150 – 800 |
| Blower Height | 500 mm | 150 – 900 |
| Primary Cyclone Diameter | 600 mm | 250 – 1000 |
| Primary Cyclone Height | 1400 mm | 600 – 2500 |
| Secondary Cyclone Diameter | 800 mm | 300 – 1400 |
| Secondary Cyclone Height | 2000 mm | 800 – 3500 |
| Air Line Diameter | 150 mm | 50 – 400 |
| Air Line Length | 1600 mm | 500 – 3000 |
| Diverter Length | 300 mm | 120 – 600 |
| Diverter Width | 300 mm | 120 – 600 |
| Diverter Height | 300 mm | 120 – 600 |
| Pant Leg Diameter | 200 mm | 80 – 400 |
| Pant Leg Height | 500 mm | 200 – 1000 |
| HEPA Filter Length | 1200 mm | 500 – 2000 |
| HEPA Filter Width | 700 mm | 300 – 1400 |
| HEPA Filter Height | 900 mm | 300 – 1800 |
| Vent Diameter | 200 mm | 80 – 500 |
| Vent Height | 400 mm | 100 – 1000 |
Every value above is a live dimension. Open a model like this in the editor and each one becomes a slider you can drag before exporting.
More models
Browse the full gallery →Trumpet Lyre Mount Main Body
A single 3D mechanical CAD part for a trumpet music lyre mount (Main Body with Paddle). Geometry details: 1. A 18mm-wide semi-cylindrical clamp arc for a 28mm diameter cylinder, w
UAV Ogive Nose Cone
Design a watertight, 3D-printable aerodynamic nose cone module for a fixed-wing tactical UAV, optimized for printing in Carbon Fiber Filled PETG (PETG-CF). The base of the nose con
Flat-Strap Reel Spool
Create a 3D model of a custom flat-strap reel spool for a home plate housing cavity. Geometry: - A reel spool consisting of two parallel circular outer flanges connected by a cent
PET Recycling Kiosk Frame
Design a production-ready welded steel frame for an outdoor PET bottle recycling and animal feeding kiosk. Create ONLY the steel frame. Do not create covers, motors, tanks, electr
Kugoo G2 Pro Rear Swingarm for KuKirin G4
Create a detailed 1:1 CAD drawing of custom rear swingarms for the Kugoo G2 Pro 2020 electric scooter. The swingarms must be designed to fit a KuKirin G4 hub motor instead of the o
Humanoid Robot Exploded Assembly
Design a 3D CAD model of a fully autonomous humanoid biped robot for the Robofest AI HOMO BOT competition. Dimensions Height: 800 mm (80 cm) Maximum weight: 20 kg Lightweight modu