Brackets and mounts
Manba One Controller Phone Mount
- Bounding box
- 129.0 × 62.5 × 200.0 mm
- Engine
- Precision B-rep
- Parameters
- 43
- Published
- September 13, 2026
Download
Free to download and use. See the terms.
The prompt
Design a functional 3D-printable smartphone holder specifically for the Manba One wireless gaming controller. IMPORTANT: This is NOT a generic Xbox or PlayStation controller mount. The holder must be designed specifically around the physical shape and dimensions of the Manba One controller. GOAL: Create a removable clip-on phone mount that attaches securely to the top/center area of the Manba One controller and holds a smartphone above the controller, similar to a traditional gaming controller phone clip. DESIGN REQUIREMENTS: 1. The mount must attach to the Manba One controller without permanently modifying, drilling, gluing, or damaging the controller. 2. Use a strong adjustable clamp mechanism that grips the controller securely but does not press buttons, analog sticks, triggers, the display, or other controls. 3. The phone holder should be centered above the controller. 4. The smartphone cradle must support phones approximately 65–90 mm wide. 5. The phone cradle should have adjustable side grips so different phone sizes can be securely held. 6. Include a slight protective lip at the bottom of the phone cradle so the phone cannot slide downward. 7. The phone holder should allow approximately 180 degrees of tilt adjustment so the viewing angle can be changed while gaming. 8. The connection between the controller clamp and phone holder should be strong enough that the phone does not wobble during normal gaming. 9. Design the parts with rounded edges and ergonomic surfaces. 10. Avoid interfering with the Manba One's buttons, analog sticks, triggers, screen, charging port, or ventilation openings. 11. Add small clearance gaps where necessary so the printed part does not rub against the controller. 12. Design the clamp with approximately 0.3–0.5 mm clearance/tolerance for FDM 3D printing. 13. The design should be optimized for PLA+ or PETG printing. 14. Prefer a modular design consisting of: - Controller mounting clamp - Adjustable arm - Phone cradle - Tilt/rotation joint 15. Use screws, pins, or standard hardware where appropriate instead of printing fragile hinges. 16. Make the parts thick and strong enough for repeated use. Avoid unnecessarily thin walls. 17. The final design must be a functional mechanical part, not an artistic 3D model. OUTPUT: Generate a clean parametric CAD model suitable for FDM 3D printing. Export the final model as: - STL for 3D printing - STEP for editing IMPORTANT: Do not assume Xbox, PlayStation, Switch Pro, or other controller dimensions. The geometry must be based specifically on the Manba One controller. If exact Manba One dimensions are unavailable, create the design parametrically with adjustable dimensions for the controller clamp so I can enter the exact measurements later.
Parameters
| Name | Value | Range |
|---|---|---|
| Clamp Channel Width | 62 mm | 30 – 120 |
| Clamp Channel Depth | 42 mm | 20 – 100 |
| Clamp Channel Height | 16 mm | 8 – 50 |
| Clamp Wall Thickness | 4 mm | 2 – 10 |
| Contact Clearance | 0.4 mm | 0 – 1 |
| Controller Body Depth | 30 mm | 22 – 38 |
| Fixed Jaw Thickness | 6 mm | 3 – 15 |
| Sliding Jaw Width | 58 mm | 20 – 110 |
| Sliding Jaw Depth | 14 mm | 6 – 30 |
| Sliding Jaw Height | 22 mm | 10 – 40 |
| T-Slot Width | 10 mm | 5 – 20 |
| Knob Diameter | 22 mm | 10 – 50 |
| Knob Thickness | 8 mm | 4 – 20 |
| Knob Screw Diameter | 4 mm | 3 – 8 |
| Knob Screw Length | 30 mm | 10 – 60 |
| Arm Width | 22 mm | 10 – 50 |
| Arm Thickness | 12 mm | 6 – 30 |
| Arm Length | 95 mm | 40 – 200 |
| Arm Slot Width | 6 mm | 3 – 15 |
| Arm Slot Length | 45 mm | 10 – 100 |
| Arm Mounting Hole | 4 mm | 2 – 10 |
| Arm Lock Screw Dia | 4 mm | 3 – 8 |
| Arm Lock Screw Length | 16 mm | 8 – 40 |
| Tilt Block Width | 32 mm | 15 – 60 |
| Tilt Block Depth | 26 mm | 15 – 60 |
| Tilt Block Height | 16 mm | 8 – 40 |
| Pivot Hole Diameter | 4.2 mm | 3 – 10 |
| Tilt Pin Diameter | 4 mm | 3 – 8 |
| Tilt Pin Length | 30 mm | 15 – 60 |
| Washer Outer Diameter | 8 mm | 5 – 16 |
| Washer Thickness | 1 mm | 0.5 – 4 |
| Cradle Width | 105 mm | 60 – 160 |
| Cradle Height | 78 mm | 40 – 140 |
| Cradle Thickness | 9 mm | 4 – 20 |
| Bottom Lip Height | 14 mm | 5 – 30 |
| Bottom Lip Depth | 8 mm | 3 – 20 |
| Grip Length | 55 mm | 20 – 120 |
| Grip Width | 14 mm | 6 – 30 |
| Grip Height | 26 mm | 10 – 60 |
| Grip Retaining Lip Height | 12 mm | 5 – 30 |
| Sliding Tenon Width | 10 mm | 4 – 20 |
| Grip Lock Screw Dia | 3 mm | 2 – 6 |
| Grip Lock Screw Length | 12 mm | 5 – 30 |
Every value above is a live dimension. Open a model like this in the editor and each one becomes a slider you can drag before exporting.
More models
Browse the full gallery →Trumpet Lyre Mount Main Body
A single 3D mechanical CAD part for a trumpet music lyre mount (Main Body with Paddle). Geometry details: 1. A 18mm-wide semi-cylindrical clamp arc for a 28mm diameter cylinder, w
UAV Ogive Nose Cone
Design a watertight, 3D-printable aerodynamic nose cone module for a fixed-wing tactical UAV, optimized for printing in Carbon Fiber Filled PETG (PETG-CF). The base of the nose con
Flat-Strap Reel Spool
Create a 3D model of a custom flat-strap reel spool for a home plate housing cavity. Geometry: - A reel spool consisting of two parallel circular outer flanges connected by a cent