Everything else
LFR Chassis with Rear Battery Pod and F1 Front Electronics Nose
- Bounding box
- 254.0 × 254.0 × 30.0 mm
- Engine
- Precision B-rep
- Parameters
- 41
- Published
- November 21, 2026
Download
Free to download and use. See the terms.
The prompt
KEEP YOUR DESIGN IN TW PARTS ONE THE BACK PARST AN AERODYNAMIC SHAPE OF 10 INTO 5 CM DIMENSIONS HAVING AN AREA HIGH FROM BASE TO PUT BATTERY TWO TYRES POSITION ON THE END OF THE BASE TO PLACE TYRES WITH MOTORS POTIONS TO ATTACH THE BATTERY COMPARTMENT IS ATTACHED WITH THE FRONT PART HIGH FROM THE BASE WITH SHAPE OF THE FRONT SIDE OF AN F1 CAR THE PART IS HAVING A SENSOR BELOW IT AND SOME CHIP POSITIONS ABOVE IT
Parameters
| Name | Value | Range |
|---|---|---|
| Chassis Length | 254 mm | 200 – 254 |
| Chassis Width | 254 mm | 200 – 254 |
| Plate Thickness | 2.8 mm | 2 – 3 |
| Corner Radius | 8 mm | 0 – 25 |
| Sensor Count | 5 | 2 – 8 |
| Sensor Pitch | 15 mm | 10 – 25 |
| Sensor Row Y Offset | 105 mm | 80 – 120 |
| Sensor Hole Diameter | 5 mm | 2 – 8 |
| Caster Hole Spacing | 24 mm | 15 – 40 |
| Caster Pattern Y Offset | 115 mm | 90 – 125 |
| Mounting Hole Diameter | 3.2 mm | 2 – 6 |
| Controller Hole DX | 50 mm | 20 – 80 |
| Controller Hole DY | 40 mm | 20 – 80 |
| Controller Pattern Y Offset | 30 mm | 0 – 80 |
| Motor Slot X Offset | 72 mm | 30 – 120 |
| Motor Slot Y Offset | 95 mm | 60 – 125 |
| Motor Hole Spacing | 24 mm | 12 – 50 |
| Motor Slot Length | 12 mm | 6 – 25 |
| Motor Slot Width | 3.2 mm | 2 – 8 |
| Battery Strap Y Offset | -55 mm | -120 – 0 |
| Battery Strap Spacing | 45 mm | 20 – 80 |
| Battery Slot Length | 18 mm | 10 – 35 |
| Battery Slot Width | 5 mm | 3 – 10 |
| Lightening Slot Width | 8 mm | 4 – 20 |
| Lightening Slot Length | 35 mm | 15 – 80 |
| Rear Battery Pod Length | 100 mm | 60 – 140 |
| Rear Battery Pod Width | 50 mm | 30 – 80 |
| Rear Battery Pod Height | 28 mm | 12 – 50 |
| Rear Battery Wall Thickness | 3 mm | 2 – 6 |
| Rear Battery Floor Thickness | 2.5 mm | 1.5 – 6 |
| Rear Pod Edge Clearance | 5 mm | 0 – 30 |
| Front F1 Nose Length | 100 mm | 60 – 150 |
| Front F1 Nose Width | 80 mm | 40 – 120 |
| Front F1 Deck Height | 30 mm | 10 – 60 |
| Front Nose Tip Height | 5 mm | 1 – 20 |
| Front Nose Edge Clearance | 5 mm | 0 – 30 |
| Chip Pocket Width | 12 mm | 5 – 25 |
| Chip Pocket Length | 12 mm | 5 – 25 |
| Chip Pocket Depth | 1 mm | 0.3 – 3 |
| Chip Pocket X Pitch | 22 mm | 10 – 60 |
| Chip Pocket Y Offset | -5 mm | -40 – 40 |
Every value above is a live dimension. Open a model like this in the editor and each one becomes a slider you can drag before exporting.
More models
Browse the full gallery →Table
Make a table of height 45 cm
Haul‑off Reel
Make this haul off reel, the dimensions of it should be a 2 meter diameter circle shaper with 0.7 meter width, i have attached a picture of what it looks like
旋转式卷烟陈列架
物件名称: 旋转式卷烟陈列架(带语音播报) 整体形态: 一个圆柱形、可360度旋转的立式展示架。 整体高度为1380mm,直径为600mm。 底部配有4个带刹车的万向轮,方便移动和固定。 结构分层(从下往上): 底座(0-200mm高度): 底部为圆柱形底座,高200mm。 外层采用网格状设计(类似金属网孔或菱形网格)。 底座内部中空,用于内置音箱设备。
Deck with U-Shape and Stairs
ARE THOSE ALL THE SAME DEMETNIONS THT I GAVE YOU IN THE FIRST MESSAGE
Flip-Top Bottle Cap with Center Hole
我要生成類似瓶蓋跟市售一模一樣 可以上掀蓋然後打開中間會有一個洞
Rounded Rectangular Tray
tôi muốn tạo một khay hình chữ nhật dài khoảng 40x30cm, có gờ của các thành cao lên 4cm, đế dày 2cm và 4 góc được bo tròn
