Brackets and mounts
FPV Kamikaze Racing Drone Assembly
- Bounding box
- 360.9 × 360.9 × 167.0 mm
- Engine
- Precision B-rep
- Parameters
- 34
- Published
- September 13, 2026
Download
Free to download and use. See the terms.
The prompt
"A highly detailed, photorealistic, and structurally accurate 3D model of an FPV Kamikaze Racing Drone. The drone is built on a 311mm diagonal wheelbase (typical 7-inch class frame). The frame must be constructed from thick, premium matte carbon fiber, clearly showing the woven carbon fiber texture, chamfered edges, and standoffs. Core Components & Electronics: Centered on the frame, a massive 6S3P 12,000 mAh Li-ion battery pack wrapped in heat shrink, dominating the top plate. Underneath the top plate, an electronics stack featuring an F4 Flight Controller stacked on top of a heavy-duty 4-in-1 ESC module. Wiring should look realistic with thick silicone AWG cables soldered to the ESC pads. At the front, an analog FPV camera (representing 1500 TVL) mounted rigidly inside a carbon/TPU bracket, physically tilted exactly 25 degrees upwards (looking up). The lens should look slightly wide-angle (representing 125-degree FOV) with glass reflections. At the rear, an exposed 2.5W Analog VTX module with a long, thick SMA antenna (circular polarized or stubby dipole) pointing upwards. Beside it, a tiny ELRS 2.4GHz receiver module with a T-shaped (dipole) antenna mounted via a TPU printed mount. Motors & Props: Four large, aggressive brushless motors (stators visible, copper windings exposed, black and gunmetal bell housings). 7-inch polycarbonate tri-blade propellers securely fastened with nyloc nuts. Vibe & Details: The drone should look purposeful, tactical, and built for speed and endurance (25-minute flight time capacity). Weight distribution should visually make sense for a heavy 1100g build. Include ultra-fine details: zip-ties holding down wires, XT60 power connector plugged in, visible solder joints, M3 titanium screws, and slight dirt/wear to emphasize a raw, industrial, battle-ready FPV drone. Studio lighting, white background, 8k resolution, suitable for exporting as a high-quality .OBJ, .STL, or .DAE mesh."
Parameters
| Name | Value | Range |
|---|---|---|
| Central plate size | 170 mm | 140 – 220 |
| Plate thickness | 4 mm | 2 – 8 |
| Standoff height | 25 mm | 15 – 35 |
| Arm width | 20 mm | 12 – 30 |
| Arm thickness | 6 mm | 3 – 10 |
| Edge chamfer | 0.8 mm | 0.2 – 2 |
| Motor-to-motor diagonal | 311 mm | 280 – 360 |
| Standoff diameter | 6 mm | 4 – 10 |
| M3 screw diameter | 3 mm | 2 – 4 |
| Battery length | 140 mm | 100 – 180 |
| Battery width | 60 mm | 40 – 100 |
| Battery height | 50 mm | 30 – 70 |
| Electronics stack length | 36 mm | 20 – 50 |
| Electronics stack width | 36 mm | 20 – 50 |
| Electronics stack height | 20 mm | 10 – 30 |
| Camera body length | 28 mm | 20 – 40 |
| Camera body width | 28 mm | 20 – 40 |
| Camera body height | 30 mm | 20 – 40 |
| Camera upward tilt | 25 deg | 10 – 45 |
| VTX length | 40 mm | 30 – 60 |
| VTX width | 25 mm | 20 – 40 |
| VTX height | 10 mm | 5 – 20 |
| SMA antenna diameter | 15 mm | 8 – 25 |
| SMA antenna length | 100 mm | 60 – 160 |
| Receiver length | 20 mm | 12 – 30 |
| Receiver width | 12 mm | 8 – 20 |
| Receiver height | 4 mm | 2 – 8 |
| Motor diameter | 35 mm | 25 – 45 |
| Motor height | 30 mm | 20 – 40 |
| Propeller diameter | 178 mm | 150 – 210 |
| Propeller blade count | 3 mm | 2 – 5 |
| XT60 connector length | 20 mm | 12 – 30 |
| XT60 connector width | 10 mm | 6 – 20 |
| XT60 connector height | 8 mm | 5 – 15 |
Every value above is a live dimension. Open a model like this in the editor and each one becomes a slider you can drag before exporting.
More models
Browse the full gallery →Trumpet Lyre Mount Main Body
A single 3D mechanical CAD part for a trumpet music lyre mount (Main Body with Paddle). Geometry details: 1. A 18mm-wide semi-cylindrical clamp arc for a 28mm diameter cylinder, w
UAV Ogive Nose Cone
Design a watertight, 3D-printable aerodynamic nose cone module for a fixed-wing tactical UAV, optimized for printing in Carbon Fiber Filled PETG (PETG-CF). The base of the nose con
Flat-Strap Reel Spool
Create a 3D model of a custom flat-strap reel spool for a home plate housing cavity. Geometry: - A reel spool consisting of two parallel circular outer flanges connected by a cent