Gears and transmission
Foldable Quadcopter Frame Plate with Component Mounts
- Bounding box
- 168.0 × 308.0 × 12.0 mm
- Engine
- Precision B-rep
- Parameters
- 44
- Published
- October 20, 2026
Download
Free to download and use. See the terms.
The prompt
Can you add the folding mechanism to it and slots for the follow you can alter the dimensions slight based on it Raspberry Pi 5 Pixhawk/CUAV Flight Controller STL19P 2D LiDAR Front-Facing RGB Camera Downward Optical Flow Camera ToF Rangefinders T-Motor F80/F100 Brushless Motors × 4 ESCs × 4 4S LiPo Battery Power Distribution Board (PDB) Voltage Regulators (BEC/DC-DC) Telemetry Module Wi-Fi Module / Antenna Propellers × 4 Propeller Guards Folding Arm Hinges × 4 Motor Mounts × 4 Landing Gear Docking Interface / Locking Mechanism Wiring Harness and Connectors
Parameters
| Name | Value | Range |
|---|---|---|
| Body Length | 200 mm | 100 – 400 |
| Body Width | 140 mm | 80 – 300 |
| Body Thickness | 4 mm | 1 – 10 |
| Body Corner Radius | 8 mm | 0 – 30 |
| Arm Length | 90 mm | 40 – 200 |
| Arm Width | 20 mm | 10 – 40 |
| Arm Thickness | 4 mm | 1 – 10 |
| Arm Root Overlap | 10 mm | 0 – 30 |
| Hinge Y Offset | 50 mm | 20 – 100 |
| Pivot Pin Diameter | 3 mm | 1 – 10 |
| Motor Pod Diameter | 28 mm | 15 – 50 |
| Motor Pod Height | 12 mm | 5 – 30 |
| Motor Shaft Bore | 6 mm | 2 – 20 |
| ESC Mount Hole Diameter | 3.2 mm | 1 – 10 |
| ESC Mount Hole Spacing | 12 mm | 4 – 30 |
| ESC Offset from Motor Tip | 15 mm | 5 – 40 |
| Front Camera Bore | 16 mm | 5 – 40 |
| LiDAR Mount Hole Spacing | 32 mm | 10 – 60 |
| LiDAR Mount Hole Diameter | 3.2 mm | 1 – 10 |
| LiDAR Y Offset | 50 mm | -50 – 150 |
| LiDAR Optical Window Diameter | 22 mm | 5 – 50 |
| Optical Flow Camera Hole | 12 mm | 3 – 30 |
| Optical Flow Y Offset | -15 mm | -100 – 50 |
| ToF Slot Width | 8 mm | 2 – 20 |
| ToF Slot Length | 5 mm | 2 – 20 |
| ToF X Offset | 40 mm | 10 – 100 |
| ToF Y Offset | 70 mm | 10 – 150 |
| Flight Controller Hole Spacing | 30.5 mm | 10 – 60 |
| Flight Controller Hole Diameter | 3.2 mm | 1 – 10 |
| Flight Controller Y Offset | 10 mm | -100 – 100 |
| Raspberry Pi Hole Spacing X | 58 mm | 20 – 100 |
| Raspberry Pi Hole Spacing Y | 49 mm | 20 – 100 |
| Raspberry Pi Hole Diameter | 2.7 mm | 1 – 10 |
| Raspberry Pi Y Offset | -65 mm | -150 – 50 |
| Antenna Hole Diameter | 6 mm | 2 – 20 |
| Antenna Hole Inset from Tail | 10 mm | 2 – 30 |
| Battery Strap Slot Width | 8 mm | 2 – 20 |
| Battery Strap Slot Length | 50 mm | 10 – 150 |
| Battery Strap Slot Y Offset | 35 mm | 0 – 100 |
| Landing Gear Hole Diameter | 4 mm | 1 – 10 |
| Landing Gear Hole Inset | 10 mm | 2 – 30 |
| Docking Slot Width | 8 mm | 2 – 20 |
| Docking Slot Length | 24 mm | 5 – 60 |
| Docking Slot Inset from Nose | 6 mm | 2 – 20 |
Every value above is a live dimension. Open a model like this in the editor and each one becomes a slider you can drag before exporting.
More models
Browse the full gallery →Spur Gearbox
design gearbox
Involute Spur Gear with Keyway
Precision Involute Spur Gear with Hub and Keyway: Module (m) of 2.0 mm, 40 teeth (z), Pitch Circle Diameter (d) of 80.00 mm, 20° pressure angle (\alpha), 15.00 mm face width (b), a
Parametric Helical Gear
Create a parametric helical gear with the following specifications: 32 teeth, normal module of 3 mm, right-hand helix, total face width of 80 mm, and a central bore hole with a dia
Rod with Spur Gear
Metal rod diameter is 20 mm and length is 100 mm and right side attach a gear and their OD is 50 mm
Spur Gear (12 Teeth)
Built a gear with 12 teeth
Two-Stage Spur Gear Reduction Assembly
Design a 2-stage spur gear reduction set for 3D printing with an overall 10:1 ratio. Stage 1: A 12-tooth pinion driving a 36-tooth gear (3:1). Stage 2: A 12-tooth pinion coupled