Everything else
ESP32-S3 PN532 RFID Reader Case
- Bounding box
- 125 × 65 × 34.5 mm
- Engine
- 3D Printing B-rep
- Parameters
- 39
- Published
- November 18, 2026
Download
Free to download and use. See the terms.
The prompt
Benötigt wird ein Gehäuse für ein ESP32-S3-DevKitC-1 und PN532-Modul im selben Gehäuse. Das gerät soll als RFID Reader eingesetzt werden. Beide USB-C ports müssen zugänglich sein. Die RGB LED soll durch einen Lichttunnel an der Gehäuseaussenseite sichtbar sein. RST und BOOT knöpfe sollen von aussen zugänglich sein. (Löcher) Am ESP32-S3-DevKitC-1 werden dupont Stecker verwendet die an das PN532-Modul gelötet sind.
Parameters
| Name | Value | Range |
|---|---|---|
| Outer length | 125 mm | 90 – 180 |
| Outer width | 65 mm | 50 – 120 |
| Outer height | 32 mm | 24 – 60 |
| Wall thickness | 2.5 mm | 1.6 – 4 |
| Floor thickness | 2.5 mm | 1.6 – 5 |
| PCB length | 63.5 mm | 50 – 80 |
| PCB width | 25.4 mm | 20 – 40 |
| PCB centre X | -27 mm | -60 – 60 |
| PCB centre Y | 12 mm | -30 – 30 |
| PCB underside height | 8 mm | 3 – 20 |
| Standoff diameter | 5 mm | 3 – 8 |
| Standoff inset from PCB edge | 4 mm | 2 – 10 |
| PCB length | 42.7 mm | 30 – 60 |
| PCB width | 40.4 mm | 30 – 60 |
| PCB centre X | 30 mm | -50 – 60 |
| PCB centre Y | 0 mm | -30 – 30 |
| PCB underside height | 3.5 mm | 1 – 10 |
| Standoff diameter | 5 mm | 3 – 8 |
| Standoff inset from PCB edge | 4 mm | 2 – 10 |
| Floor thickness under antenna | 1.2 mm | 0.8 – 2.5 |
| Antenna recess inset | 6 mm | 2 – 12 |
| USB-C opening width | 9.5 mm | 6 – 14 |
| USB-C opening height | 4 mm | 3 – 8 |
| USB-C centre spacing | 12 mm | 6 – 20 |
| USB-C centre height | 10.2 mm | 4 – 20 |
| Button hole diameter | 4 mm | 2 – 8 |
| RST hole X | -45 mm | -60 – 60 |
| BOOT hole X | -35 mm | -60 – 60 |
| Button hole centre height | 10 mm | 3 – 25 |
| LED centre X | -52 mm | -60 – 60 |
| LED centre Y | 6 mm | -30 – 30 |
| Tube outer diameter | 6 mm | 3 – 10 |
| Tube inner diameter | 3 mm | 1.5 – 8 |
| Tube-to-PCB gap | 2 mm | 1 – 8 |
| Lid plate thickness | 3 mm | 1.5 – 6 |
| Lid lip height | 3 mm | 1 – 8 |
| Lid lip wall thickness | 2 mm | 1 – 4 |
| Lid fit clearance | 0.2 mm | 0.1 – 0.5 |
| Lid-to-base overlap | 0.5 mm | 0.2 – 1 |
Every value above is a live dimension. Open a model like this in the editor and each one becomes a slider you can drag before exporting.
More models
Browse the full gallery →Table
Make a table of height 45 cm
Haul‑off Reel
Make this haul off reel, the dimensions of it should be a 2 meter diameter circle shaper with 0.7 meter width, i have attached a picture of what it looks like
旋转式卷烟陈列架
物件名称: 旋转式卷烟陈列架(带语音播报) 整体形态: 一个圆柱形、可360度旋转的立式展示架。 整体高度为1380mm,直径为600mm。 底部配有4个带刹车的万向轮,方便移动和固定。 结构分层(从下往上): 底座(0-200mm高度): 底部为圆柱形底座,高200mm。 外层采用网格状设计(类似金属网孔或菱形网格)。 底座内部中空,用于内置音箱设备。
Deck with U-Shape and Stairs
ARE THOSE ALL THE SAME DEMETNIONS THT I GAVE YOU IN THE FIRST MESSAGE
Flip-Top Bottle Cap with Center Hole
我要生成類似瓶蓋跟市售一模一樣 可以上掀蓋然後打開中間會有一個洞
Rounded Rectangular Tray
tôi muốn tạo một khay hình chữ nhật dài khoảng 40x30cm, có gờ của các thành cao lên 4cm, đế dày 2cm và 4 góc được bo tròn
