Brackets and mounts
ESP32-8048S050 Enclosure (Top + Bottom Cover, Exploded)
- Bounding box
- 330.0 × 96.0 × 22.0 mm
- Engine
- Precision B-rep
- Parameters
- 49
- Published
- October 21, 2026
Download
Free to download and use. See the terms.
The prompt
Create a 2-piece electronics enclosure for an ESP32-8048S050 development board. Requirements: - Overall style: clean consumer electronics enclosure. - Two parts: 1. Top cover with display window. 2. Bottom cover with mounting posts. Board: - ESP32-8048S050, 5.0-inch touchscreen display. - PCB dimensions approximately 140 mm x 86 mm. - PCB thickness 1.6 mm. Top Cover: - Outer corner radius: 8 mm. - Wall thickness: 2.5 mm. - Front bezel width: 8 mm around LCD. - LCD viewing window centered. - LCD opening size: 110 mm x 67 mm. - Recess display 1.5 mm below front surface. - Four internal alignment pins matching bottom cover. - Vent slots near ESP32 area. Bottom Cover: - Wall thickness: 2.5 mm. - Internal clearance above components: 12 mm. - Four M3 standoffs located at PCB mounting holes. - Standoff height: 6 mm. - Brass heat-set insert pockets for M3 screws. - USB access opening on side. - Power connector opening on side. - SD card access opening if present. - Speaker cable exit slot. - Ventilation openings near processor. Assembly: - Join using 4 M3 screws from bottom into inserts in top cover. - 0.3 mm clearance between mating parts. - Designed for FDM printing without support. - Chamfer bottom edges 1 mm. - Include embossed label: "ESP32-8048S050" Output: - Separate printable top cover and bottom cover. - Optimized for PLA or PETG.
Parameters
| Name | Value | Range |
|---|---|---|
| Overall Width (X) | 150 mm | 100 – 220 |
| Overall Depth (Y) | 96 mm | 60 – 160 |
| Wall Thickness | 2.5 mm | 1.6 – 5 |
| Top Cover Height | 12 mm | 6 – 30 |
| Bottom Cover Height | 18 mm | 8 – 40 |
| Front Plate Thickness | 4 mm | 2.5 – 8 |
| LCD Window Width | 110 mm | 40 – 160 |
| LCD Window Height | 67 mm | 30 – 120 |
| Display Recess Depth | 1.5 mm | 0.5 – 4 |
| Bezel Lip Overhang | 5 mm | 1 – 12 |
| Top Screw Boss Diameter | 7 mm | 4 – 14 |
| Top Screw Boss Height | 6 mm | 3 – 15 |
| M3 Heat-Set Insert Pocket Dia | 4.2 mm | 3.2 – 6 |
| M3 Insert Pocket Depth | 5 mm | 2 – 10 |
| Alignment Pin Diameter | 3 mm | 1.5 – 6 |
| Alignment Pin Length | 12 mm | 4 – 25 |
| Alignment Pin X Position | 60 mm | 10 – 72 |
| Alignment Pin Y Position | 26 mm | 8 – 45 |
| Top Vent Slot Row (Y) | 40 mm | 20 – 46 |
| Vent Slot Width | 2 mm | 0.8 – 6 |
| Vent Slot Length | 8 mm | 3 – 30 |
| Vent Slot Count | 6 pcs | 2 – 12 |
| Vent Slot Pitch | 6 mm | 3 – 20 |
| Floor Vent Row (Y) | -24 mm | -44 – -5 |
| Standoff X Position | 65 mm | 20 – 72 |
| Standoff Y Position | 38 mm | 20 – 45 |
| Standoff Diameter | 6 mm | 4 – 12 |
| Standoff Height | 6 mm | 3 – 15 |
| M3 Screw Clearance Hole | 3.2 mm | 2.6 – 4.5 |
| Alignment Pillar Diameter | 6 mm | 4 – 12 |
| Alignment Pin Hole Dia | 3.3 mm | 1.8 – 6.5 |
| Alignment Pin Hole Depth | 6 mm | 2 – 15 |
| USB Opening Width | 12 mm | 6 – 25 |
| USB Opening Height | 6 mm | 3 – 15 |
| USB Opening Y Offset | 20 mm | -40 – 40 |
| USB Opening Z Centre | 7 mm | 3 – 16 |
| Power Jack Opening Width | 10 mm | 5 – 22 |
| Power Jack Opening Height | 6 mm | 3 – 15 |
| Power Jack Y Offset | -20 mm | -40 – 40 |
| Power Jack Z Centre | 7 mm | 3 – 16 |
| SD Card Slot Width | 14 mm | 6 – 28 |
| SD Card Slot Height | 3 mm | 1.5 – 10 |
| SD Card Slot X Offset | 35 mm | -60 – 60 |
| SD Card Slot Z Centre | 5 mm | 2 – 16 |
| Speaker Cable Slot Width | 10 mm | 4 – 25 |
| Speaker Cable Slot Height | 3 mm | 1.5 – 10 |
| Speaker Cable Slot X Offset | -35 mm | -60 – 60 |
| Speaker Cable Slot Z Centre | 5 mm | 2 – 16 |
| Exploded Layout Gap | 30 mm | 5 – 120 |
Every value above is a live dimension. Open a model like this in the editor and each one becomes a slider you can drag before exporting.
More models
Browse the full gallery →Trumpet Lyre Mount Main Body
A single 3D mechanical CAD part for a trumpet music lyre mount (Main Body with Paddle). Geometry details: 1. A 18mm-wide semi-cylindrical clamp arc for a 28mm diameter cylinder, w
UAV Ogive Nose Cone
Design a watertight, 3D-printable aerodynamic nose cone module for a fixed-wing tactical UAV, optimized for printing in Carbon Fiber Filled PETG (PETG-CF). The base of the nose con
Flat-Strap Reel Spool
Create a 3D model of a custom flat-strap reel spool for a home plate housing cavity. Geometry: - A reel spool consisting of two parallel circular outer flanges connected by a cent
PET Recycling Kiosk Frame
Design a production-ready welded steel frame for an outdoor PET bottle recycling and animal feeding kiosk. Create ONLY the steel frame. Do not create covers, motors, tanks, electr
Kugoo G2 Pro Rear Swingarm for KuKirin G4
Create a detailed 1:1 CAD drawing of custom rear swingarms for the Kugoo G2 Pro 2020 electric scooter. The swingarms must be designed to fit a KuKirin G4 hub motor instead of the o
Humanoid Robot Exploded Assembly
Design a 3D CAD model of a fully autonomous humanoid biped robot for the Robofest AI HOMO BOT competition. Dimensions Height: 800 mm (80 cm) Maximum weight: 20 kg Lightweight modu