Enclosures and housings
Electronics Mounting Base Plate with Three Enclosures
- Bounding box
- 180.0 × 160.0 × 19.0 mm
- Engine
- Precision B-rep
- Parameters
- 25
- Published
- September 6, 2026
Download
Free to download and use. See the terms.
The prompt
Create a flat rectangular base plate 180mm along the X-axis, 160mm along the Y-axis, and 3mm thick. On the top face, generate three separate non-overlapping enclosures with 2mm thick walls and a 1mm inward-facing lip along the top inside edge: Breadboard enclosure: Inner dimensions 166mm (X) by 56mm (Y) with 8mm tall walls. Position this centered along the back Y-edge (Y = 100mm to 156mm). Battery enclosure: Inner dimensions 60mm (X) by 90mm (Y) with 15mm tall walls. Position this flush against the front-left corner (X = 5mm, Y = 5mm). Power bank enclosure: Inner dimensions 65mm (X) by 100mm (Y) with 15mm tall walls. Position this flush against the front-right corner (X = 110mm, Y = 5mm). Cut exactly four 3.2mm diameter circular screw holes straight through the 3mm base plate. Place one hole exactly 5mm inward from each of the four extreme corners of the plate. Finally, cut two 20mm by 10mm rectangular slots straight through the center base plate between the front and rear enclosures for cable routing.
Parameters
| Name | Value | Range |
|---|---|---|
| Plate Length | 180 mm | 100 – 300 |
| Plate Width | 160 mm | 80 – 250 |
| Plate Thickness | 3 mm | 1 – 10 |
| Wall Thickness | 2 mm | 1 – 5 |
| Lip Depth (inward) | 1 mm | 0.5 – 3 |
| Lip Height | 1 mm | 0.5 – 3 |
| Breadboard Inner Length (X) | 166 mm | 100 – 200 |
| Breadboard Inner Width (Y) | 56 mm | 30 – 100 |
| Breadboard Wall Height | 8 mm | 5 – 20 |
| Breadboard Y Start (from front edge) | 100 mm | 50 – 104 |
| Battery Inner Length (X) | 60 mm | 30 – 100 |
| Battery Inner Width (Y) | 90 mm | 50 – 120 |
| Battery Wall Height | 15 mm | 8 – 30 |
| Battery X Start (from left edge) | 5 mm | 0 – 116 |
| Battery Y Start (from front edge) | 5 mm | 0 – 66 |
| Power Bank Inner Length (X) | 65 mm | 30 – 100 |
| Power Bank Inner Width (Y) | 100 mm | 50 – 130 |
| Power Bank Wall Height | 15 mm | 8 – 30 |
| Power Bank X Start (from left edge) | 110 mm | 0 – 111 |
| Power Bank Y Start (from front edge) | 5 mm | 0 – 56 |
| Screw Hole Diameter | 3.2 mm | 2 – 6 |
| Corner Offset (inward from edge) | 5 mm | 2 – 20 |
| Cable Slot Length (X) | 20 mm | 10 – 40 |
| Cable Slot Width (Y) | 10 mm | 5 – 20 |
| Slot Separation (center-to-center) | 30 mm | 10 – 60 |
Every value above is a live dimension. Open a model like this in the editor and each one becomes a slider you can drag before exporting.
More models
Browse the full gallery →Cylindrical Stainless Steel Basket with Folding Handles
Design a cylindrical 304 stainless steel basket with an outer diameter of 200 mm and height of 250 mm. The basket has solid side walls with no perforations. The bottom plate contai
Spur Gearbox
design gearbox
Trumpet Lyre Mount Main Body
A single 3D mechanical CAD part for a trumpet music lyre mount (Main Body with Paddle). Geometry details: 1. A 18mm-wide semi-cylindrical clamp arc for a 28mm diameter cylinder, w